table of Contents
1, hardware installation: (For details, please refer to the quick installation manual) .................................... .......................................... 3
2, software settings: ........................................... ................................................ ................ 3
2.1, necessary settings in routing mode ....................................... ............................................ 3
2.2, necessary settings in bridging ....................................... .............................................. 4
2.3, PPPOE setting: ........................................ ................................................ 5
2.4, add a PVC connection application method: .................................... ................................ 6
2.4.1 VC1 setting: ......................................... .............................................. 6
2.4.2 VC2 setting: ......................................... ............................................ 7
EA700A application setting method
1. Hardware installation: (For details, please refer to the quick installation manual)
2, software settings:
After the EA700A is connected, use the Telnet connection to the SMT setting menu, the EA700A default IP address is 192.168.1.1, the default entry password is "1234". When you successfully enter the SMT menu, follow the procedures below.
2.1, the necessary settings in routing mode
First, you should get the following information from ISP:
VPI / VCI number, package mode, multiplexing mode, IP address (dynamic, or static)
Then fill in the appropriate settings as described below.
Menu 1 - General Setup
System name = CHT
Location =
Contact person's name =
Route IP = YES
Route ipx = no
Bridge = no
Menu 4 - Internet Access Setup
ISP's name = CHT
ENCAPSULATION = RFC 1483 <- Package Package mode (RFC1483, PPP is RFC2364)
Multiplexing = llc-based <- Press air switching multiplexing mode
VPI # = 0
VCI # = 33 Write the corresponding VPI / VCI
My login = n / a
My password = n / a
SINGLE User Account = YES
IP address assignment = DYNAMIC Press vacancy to get IP or specify static IP
IP address = n / a
ENET Encap Gateway = N / A
2.2, necessary settings in bridging
When using a special line bridge mode, it is necessary to set the EA700A to a bridging method.
Menu 1 - General Setup
System name = CHT
Location =
Contact person's name =
Route IP = NO
Route ipx = no
Bridge = yes
Menu 4 - Internet Access Setup
ISP's name = CHT
Encapsulation = RFC 1483 <- Package Package Package by Air
Multiplexing = llc-based <- Press air switching multiplexing mode
VPI # = 0
VCI # = 33 Write the corresponding VPI / VCI
My login = n / a
My password = n / a
SINGLE User Account = no Press space to switch to NO
IP address assignment = N / a
IP address = n / a
ENET Encap Gateway = N / A
Menu 11.1 Remote Node Setup
Rem node name = changeme route = no <- Switch to NO by space
Active = yes bridge = yes <- Switch to YES by space
Encapsulation = RFC 1483 Edit PPP Options = N / A
Multiplexing = llc-based Rem IP Addr = N / A
Incoming: Edit IP / IPX / Bridge = NO
Rem login = n / a
Rem password = n / a
Outgoing: session options:
My login = n / a edit filter sets = no
My password = n / a
Authen = N / A
2.3, PPPOE setting:
First, you should get the following information from ISP:
Determine this line has been set to be a PPPoE dial-up mode;
PPPOE's VPI / VCI (many regional line mode and PPPoE dial mode uses different VPI / VCI,);
PPPoE username / password (format is: username @ serviceename / password)
1. IP routing = yes in Menu 1; bridge = no
2. Menu 4
Menu 4 - Internet Access Setup
ISP's name = changeme
Encapsulation = PPPOE
Multiplexing = llc-based
VPI # = 2
VCI # = 22
Service name = CSO
My login = kevin
My password = ******* Single user account = yes
IP address assignment = Dynamic
IP address = n / a
ENET Encap Gateway = N / A
3. The MENU 4 settings will be automatically mapped into the MENU 11, but it should also be noted that set to routing mode in MENU 11.
Menu 11.1 - Remote Node Profile
Rem node name = changeMe route = ip
Active = yes bridge = no
Encapsulation = PPPOE Edit PPP Options = NO
Multiplexing = llc-based Rem IP Addr = 0.0.0.0
Incoming: Edit IP / IPX / Bridge = NO
Rem login =
Rem Password = ********
Outgoing: session options:
My login = kevin Edit filter sets = no
My password = ******** PPPOE Idle Timeout (sec) = 0
Authen = chap / pap pppoe service name = CSO
Schedule sets =
4. For the settings of the LAN:
When the EA700A is specified as DHCP Server: set to automatically obtain the IP address on the PC.
When the EA700A is not specified for DHCP Server, set the IP address of the PC in the LAN with the LAN IP address of the EA700A in Menu 3.2, and set the MODEM to the default gateway on the PC.
2.4, add a PVC connection application method:
PC ------ EA700A ------------------------ ISP --------- Internet
| ______Vod server.
If you are behind DSLAM, you need to set up in Menu1, Menu4, and then do two VC settings in Menu11 in Menu1, and then do two VCs in Menu11:
The VPI / VCI should be provided by the local part
It is assumed here that the settings given to the local end are:
VC1: VPI / VCI 0/33 Bridge to ISP
VC2: VPI / VCI 0/34 Bridge to VOD Server.
Menu 11 ---- Remote Node Setup
1. Changeme (ISP, SUA)
2. __________________
3. __________________
4. __________________
5. __________________
6. __________________
7. __________________
8. __________________
2.4.1 Settings of VC1:
Select 1 in MENU 11 to enter the first VC setting:
Menu 11.1 - Remote Node Profilerem Node Name = Bridge1 Route = NONE
Active = yes bridge = yes
Encapsulation = RFC 1483 Edit PPP Options = N / A
Multiplexing = llc-based Rem IP Addr = N / A
Incoming: Edit IP / IPX / Bridge = YES ---- Enter the next menu
Rem login = N / A See the figure Menu11.3
Rem password = n / a
Outgoing: session options:
My login = n / a edit filter sets = no
My password = n / a pppoe idle timeout (sec) = n / a
Authen = n / a pppoe service name = n / a
Menu 11.3 - Remote Node NetWork Layer Options
VPI / VCI (LLC-MUX or PPP / PPPoE ENCAP): IPX Options:
VPI # = 0 Rem Lan Net # = N / A
VCI # = 33 Enter the first VC number My Wan Net # = N / A
IP Options: hop count = n / a
REM IP Addr: N / A Tick Count = N / A
Rem subnet mask = n / a w / d spoofing (min) = n / a
My Wan Addr = N / A SAP / RIP TIMEOUT (MIN) = N / A
Single user account = n / a dial-on-query = N / a
Metric = n / a
Private = n / a
Rip Direction = N / A
Version = N / a bridge options:
Multicast = N / a Dial-on-Broadcast = N / A
IP policies = n / a ethernet addr timeout (min) = 0
2.4.2 Setting of VC2:
Select 2 in MENU 11 Enter the setting of the second VC:
Menu 11.1 - Remote Node Profile
Rem node name = bridge2 route = none
Active = yes bridge = yesencapsulation = RFC 1483 Edit PPP Options = N / A
Multiplexing = llc-based Rem IP Addr = N / A
Incoming: Edit IP / IPX / Bridge = YES ---- Enter the next menu
Rem login = N / A See the figure Menu11.3
Rem password = n / a
Outgoing: session options:
My login = n / a edit filter sets = no
My password = n / a pppoe idle timeout (sec) = n / a
Authen = n / a pppoe service name = n / a
Menu 11.3 - Remote Node NetWork Layer Options
VPI / VCI (LLC-MUX or PPP / PPPoE ENCAP): IPX Options:
VPI # = 0 Rem Lan Net # = N / A
VCI # = 34 Enter the second VC number My Wan Net # = N / A
IP Options: hop count = n / a
REM IP Addr: N / A Tick Count = N / A
Rem subnet mask = n / a w / d spoofing (min) = n / a
My Wan Addr = N / A SAP / RIP TIMEOUT (MIN) = N / A
Single user account = n / a dial-on-query = N / a
Metric = n / a
Private = n / a
Rip Direction = N / A
Version = N / a bridge options:
Multicast = N / a Dial-on-Broadcast = N / A
IP policies = n / a ethernet addr timeout (min) = 0
The IP address of the PC is specified as the same network segment with the VODSERVER on the user's PC. When the user needs to be internet, the PPPoE's dial-up software dialing is used.
Address: 2nd Floor, Building 4, Huaxing Industrial Village
Tel: 0571-85124807
Zip code: 310013
