ADSL MODEM [Port Mapping] Complete Works Port Mapping Principles
One computer in the intranet is to go to the Internet, and the port mapping port mapping is divided into dynamic and static dynamic port mapping: one computer in the intranet is to access the Sina.com, send a packet to the NAT gateway, including the other party in the header ( It is the new wave network) IP, port and native IP, port, NAT gateway will replace this unit IP, port, a unused port, and record this mapping relationship, for future forwarding packets use. Then send the data to Sina.com. Sina is reacting after receiving the data, sending data to the unused port of the NAT gateway, then the NAT gateway forwards the data to the computer in the intranet, realize the intranet and Communication. When the connection is closed, the NAT gateway releases the port assigned to this connection so that the next connection can continue to use. Dynamic port mapping is actually a way of working in the NAT gateway.
Static port mapping: is an open port on the NAT gateway, then set the data received by this port to forward to the intranet which IP and port, no matter whether it is connected, this mapping relationship will always exist. You can let the public access to a computer in the intranet
The NAT gateway can be a switch, a router, or a computer.
What is intranet, what is a public network, what is NAT?
Nowadays, there are still a serious misleadors about port mapping, many people who don't understand use port mapping software on their own computer, in fact, port mapping is to do on the gateway! ! ! The gateway is rarely a computer, and most people cannot control the gateway, so the software mapped by the port is basically useless.
Port Setting Method of Alcate Speed Touch 515
1. First enter the MODEM web setting page. 2. Open the "Configuration" menu on the left and click the "Security" item. 3. Click "Configure Nat to Internal Interfaces" in the bottom right. 4. Click on "Configure Global Address Pools and Reserved Mappings" in the middle. 5. Click on the fourth "Add Reserved Mappings" 6, "Global IP Address" to fill in "0.0.0.0". 7. "Internal IP Address" fills in your PC intranet IP (typically 10.0.0. *) 8, "Transport" selected "TCP". 9, "Port Number" (port) fills the port of the BT (BT defaults 6881-6889). 10. Click "Apply" to save the data. 11. Click "Save Config" to save the settings in the left menu.
Alcate SpeedTouch HomePlus511 ADSL Port Mapping Method
1. In the address bar input 10.0.0.138 Enter the ADSL's web setting page, click Advanced-Nat 2 on the left. After entering the NAT setting interface, the NEW on the right is created to create a new port map 3, you need to pay attention, protocol must Choose TCP, Inside IP 10.0.0.1, Outside IP to fill in 0.0.0.0.0, Inside Port, and Outside IP, the default BT port ranges from 6881 ~ 6999, and the specific look at your BT client setting. Press Apply to confirm. 4. After pressing Apply, the port mappings we have just set up will appear below Napt Settings. To perform port mapping, you can click New, step, and above.
Note: After the setting is completed, the Save all saved settings left on the upper left corner, otherwise the NAT of Modem will be automatically emptied, but also set.
ADSL (All 1100 White) Setting Method for MODEM Port Mapping
Enter this address in the browser address bar http://192.168.0.2/doc/setvs.htm If you are prompted to enter the user and password, the default is the user: admin Password: 12345678 (or 123456) can see the above interface
Then you can start setting up. 1, "public port", "private port" fill in the port you want (BT default: 6881-6889). 2, "Port Type" select "TCP". 3, "Host IP Address" Fill in the intranet IP of the PC. Then press "Add this setting". Until you all have the port you want to do. 4. Enter "192.168.0.2" in the browser to enter the following interface, click "Save Set", ADSL will restart, everything is OK!
ADSL Zhanda 2110EH Router port setting method
Juda ADSL 2110EH ROUTER IP = 192.168.10.1 Using http://192.168.10.1 in IE to enter Juda ADSL2110EH Router Management Configuration Page, Select Services - Nat Rule Configuration - Nat Options: Nat Rule Entry- -Add - enter the port mapping Add a setup section page, and the settings are as follows: The BT port mapping setting parameters are as follows:
Rule ID: 2 (changed to 3. Create a second port) Rule Flavor: RDR if Name: All Protocol: Any Local Address from: 192.168.10. * (Introduction IP) Local Address to: 192.168. 10. * (Net IP) Global Address from: 0.0.0.0 Global Address To: 0.0.0.0 Destination Port from: 6881 (BT Port) Destination Port to: 6881 (BT Port) Local Port: 6881 (BT port)
Set 1-9 (6881-6889) as needed. After setting, select Submit Submit, and finally select Admin - Commit & Reboot - Restart MODEM.
Port mapping method of ADSL ASUS 6000EV / 6005HW MODEM
According to the web address of the book, enter the MODEM web setting page. In the main menu, click "NAT", there will be a "natchannellist", fill in the following in MupltiPortForward inside Natchannellist: Action: add channelno: 1 (changed to 2 When doing the second, this type is pushed) Protocol: TCP incomingport , Begin: 6881 (BT port), end: 6881 (Doing a second time to 6882, in this class) NewPortBegin: 6881 (BT port), end: 6881 (changed to 6882 when doing the second time, Newipaddress: 192.168.1. * (Intranet IP)
Don't forget to save the settings.
Explanation: If your MODEM has turned on the routing function, it is often the automatic dialing, boot Internet, browser Internet access, etc. In order to fully reflect the charm of the BT speed, port mapping is required.
Port mapping settings for cancel 642 ADSL MODEM
Method: Enter the Zynos system after entering a Telnet 192.168.1.1 in the run or the MSDOS window (the factory default is 1234), you can enter the Zynos system, you will see the main menu as shown below CopyRight (C) 1994 - 2000 Zyxel Communications Corp. Prestige 642R-11 Main MenuGetting Started Advanced Management 1. General Setup 21. Filter Set Configuration 3. Ethernet Setup 22. SNMP Configuration 4. Internet Access Setup 23. System Password 24. System Maintenance 25. IP Routing Policy Setup Advanced Applications 11. Remote Node Setup 12. Static Routing Setup 15. SUA Server Setup 99. EXIT
Enter Menu 11.1 - Remote Node Profile
Rem node name = change = ip Active = yes bridge = no
Encapsulation = pppoe edit ppp options = no multiplexing = llc-based Rem IP addr = 0.0.0.0 incoming: edit ip / ipx / bridge = no rem login = trans password = ******* OUTGOING: session options: My Login = CZZ7205800 @ adsl edit filter set = no password = ******** PPPOE Idle Idle Timeout (sec) = 0 Authen = chap / PAP PPPOE Service Name = Schedule Sets =
Press Enter to Confirm or Esc To Cancel:
Note that after the Edit Filter sets = NO space bar is changed to YES, enter the following menu:
Menu 11.5 - Remote Node Filter
Input filter sets: protocol filters = 6 device file file = output filter sets: protocol filter sets: protocol filter sets: protocol filter sets: protocol filter file = device filter filter filter file = = DEVICE FILTERS =
Enter Here to Confirm or Esc to Cancel:
The 6 space bar will be removed after the return storage is returned to the Edit Filter sets = no, do not take it, return the board after entering the market 15
Menu 15 - SUA Server Setup
Port # ip address -------------------- 1.Default 192.168.1.2 (map all ports to this machine) 2. 0 0.0.0 3. 0 0.0.0.0 4. 0 0.0.0.0 5. 0 0.0.0.0 6. 0 0.0.0.0 7. 0 0.0.0.0 8. 0 0.0.0.0
Press Enter to Confirm or Esc To Cancel:
DB102, 108 Raiders (Routing Method, Port Mapping Method, Brush BIOS Method, Electronic Manual, USB Drive) 1. Routing Setting Method:
1. Principal-hardware connection, the device randomly comes with a parallel network cable for 1 meter! If you use this line, you need to insert the Hub's UPLINK port, or you have a cross-network cable, then you can plug it to any UPLINK. Interface! Confirm that the correct or not: Whether the PC indicator of the device lights up! Light up OK!
2. Network configuration, pay attention to the adapter and TCP / IP to properly install the protocol! Add "192.168.1.1" in the gateway to the host name and address of the DNS configuration, "192.168.1.1" in the IP address tag Between the settings of your IP (192.168.1.2 ---- 192.168.1.254), because you have to travel with your device! Confirm correct or not: Type the following command in operation "ping 192.168.1.1" See if it is connected timeout! Do not email! If your system is 2000 or XP, simply select automatically acquire IP and DNS.
3. Open the IE browser, enter "192.168.1.1" at the address bar, then enter your username and password! You can find it in your manual! Here I entered "admin" and "Dare" factory The default user and password! If you can't access it, please use the needle to the reset hole three times in the case of energization, you can enter (the cat is set up)! 4. Click the WAN under the left side, this is the side page to enter the settings! Here is the most important, I am from Hubei, and the specific settings will ask you the local telecommunications department! The lowermost virtual circuit selection "0 "After" Submit ", the upper enabled enabled YES, VPI adds 0, VCI Add 35, static IP and subnet mask are added" 0.0.0.0 ", package protocol selection" disabled "user name and Advance your password to apply for a telecommunications application! Disconnect the connection interval to enter the value you want, and enter 0 permanent connection! Check "Auto"! Automatically connect the option box to check! DHCP is dependent on your situation! I didn't set it! The gateway maintained the default "0.0.0.0" in some submission, see if your settings have changed, no saving on the left side. (Will restart the device, the LINK indicator of the device remains constant !)
5. Continue to the interface of WAN, this time the virtual circuit selected "1" submit, will enable "No", VCI, VPI add 0, static IP and subnet mask to add "0.0.0" , The package protocol is selected "PPPOE LLC", bridges "disabled", automatically connects the library box is not available! Other maintenance defaults! Submit, then save the settings, the device is restarted! So repeated until the virtual circuit is 7 Talent! I am set up like this, numbness is trouble, other methods seem to have nothing.
6. After the device is stable, now "NAT" below WAN, select "NAPT" in the drop-down menu on the right, click, save, and the device is restarted!
7. In the last step, click on the DNS under NAT, then the DNS agent in the next right interface select "Use Aoto Discovered DNS Servers Only", other non-moving, submit, save settings, and device restart!
It should be available now! If you don't do it, you will have a mistake in "System Log" and "Diagnostic Test"! Below is the system log after I succeed:
7/12/2003 1:51:24> Received Time From Time Server 128.138.140.44 1/1/1970 0: 0: 0: 21> PPP1 session is up. 1/1/1970 0: 0: 20> NAPT: MANY- To-One Default Session IS Up. 1/1/1970 0: 0: 20> NAT / NAPT Session Start: VC # 0, WAN IP IS 219.109.29.2 1/1/1970 0: 0: 20> PPP1: DNS Secondary IP Address IS 202.203.44.5 1/1/1970 0: 0: 20> PPP1: DNS Primary IP Address IS 202.203.0.117 1/1/1970 0: 0: 20> PPP1: PPP Gateway IP Address IS 61.166.227.1 1 / 1/1970 0: 0: 20> PPP 1: PPP IP Address IS 219.109.29.2 1/1/1970 0: 0: 20> PPP PAP Authentication Success 1/1/1970 0: 0: 15> PPP1 PPPoE session is established. 1/1/1970 0: 0: 0: 11> ADSL Connected 1/1/1970 0: 0: 11> ATM Layer IS Up, Cell Delineation Achieved 1/1/1970 0: 0: 11> ATM Connected 1/1/1970 0: 0: 0> Initialized napt. 1/1/1970 0: 0: 0> NAPT IS enabled 1/1/1970 0: 0: 0> ATM: Setting Up VCC0, VPI = 0, VCI = 35 1/1 / 1970 0: 0: 0> ATM: Detected 1/1/1970 0: 0: 0> Ethernet device 0 detected two, brush BIOS method 1. First supplied driver decompressed copy to a target on the computer, folder name Use English, such as: D: / Flash. 2. Select all the files after the decompression, and right click, select "Properties" in the pop-up menu, such as "Reading" in "Properties" is selected, you need to change it to "Archive ". 3. Boot the computer with Windows 98 to boot the computer and enter the "MS-DOS" state. (Or Restart in WIN98 and enter MS-DOS ") 4. Connect the computer's USB 1 and ADSL MODEM 5. ADSL MODEM with USB cable. 6. Change the current directory of the computer to D: / Flash. 7. Enter the command: EW1 or 4 (Note: EW1 is used for DB102-B and DB108, EW4 for DB102 and DB102-a) 8. When "START Ethernet LAN Mac (00-08-5C-10-00-00 : "Enter the MAC value below the back of the ADSL housing. 9. When "ETHERNET LAN MAC (00-08-5C-10-FF-FF) appears:", press Enter. 10. The following screen indicates that the corresponding program is successfully written.
Setting up the usb interface ... set size of sdram to 8MB size of flash is 2MB manufacture ID = 0 × 00c2 device id = 0 × 2249 Reading 'mxic.bin' ... Reading 'Firmware.dif' ... Flash programming in progress .. Flash Programming complete Please see status of LEDs to determine success Four Solid LWSs = Success No LEDs = ERROR D:. / flash> D:. / flash> 10 unplug the USB cable, a power switch off ADSL Modem . The prize ADSL MODEM is then re-powered, and the boot program will reboot (this process will be greater than 1 minute). When the LINK light is flashing, it means that the boot is completed.
Third, the big Asia DB108 and 102 port pilot setting method
Since this device has already opened the routing function, the problem is coming again, my own computer wants to become a website, can you call someone to visit my computer or FTP? It is very simple! Enter the advanced configuration in its device It is possible .ip address http://192.168.1.1/doc/index1.htm; see there is a virtual server above? If you enter, add the IP you want to do in the station! Fill in the port, even if the setting is successful, Submitted, this time your computer can say it. Don't be busy, don't be excited, and the most critical problem is not solved, that is, the ADSL management port of this device and the computer port you have stated. 80, How do you have access to your specified server when you visit, how to solve this problem? Then you have to find other configurations in this device, you don't want to take it directly to see the HTTP server port 80. It is OK to make your own thinking! This time you submit it, you can call someone to visit your site from the outside. Finally, you can access your ADSL. HTTP: //192.168. 1.1! So you can't enter your ADSL device, if I turn the port modification into 81, I will go to the ADSL device in the future, then I only http://192.168.1.1.1:81 with this in IE. Port into ... Mold Cherry lying 躺 福? / A>
Key Tip: IP address http://192.168.1.1/doc/index1.htm; see there is a [virtual server] not? After entering, add the IP you want to do to stand up! Fill in the port, even if the setting is successful. Submitted, this time your computer can say that it is emitted.
Emma Adsl Modem, BT Internet speed
System: Windows XP Pro Net: ADSL Routing, Self-built LAN ADSL MODEM: IM 701G (Emma, White) Bandwidth: 2M BT Version: 5.2.1 1kb / s before speeding up: 100kb / s (20 seeds)
Method: 1. Port mapping: The most started in the XP network attributes, useless! Enter ADSL settings, ---- Safety settings ---- NAT advanced configuration ...---- Added RESERVED MAPPING ... Add 6881-6885 5 port mapping, (enough, generally only one BT)
As follows:
The IP address transfer type port number and interface address inside the Global IP address are the same as 192.168.101. * TCP 6881 delete ... and interface addresses The same 192.168.101. * TCP 6882 delete ... and interface addresses identical 192.168.101. * TCP 6883 deletes ... and interface addresses the same 192.168.101. * TCP 6884 delete ... and interface addresses the same 192.168.101. * TCP 6885 delete ... save ---- Restart device
2, turn off the XP firewall, in the network attribute
3, different ADSL Modem setup methods are different, but they must be modified in security settings, find reserved mapping or port mapping
ZTE White Horizontal ADSL831 Port Map
First, first confirm that your ZTE ADSL831 has turned on the routing function and can be accessed normally. Other related posts can be seen in the routing method. Second, set this unit to 192.168.1.2-192.168.1.xxx three, click Start - run, enter the CMD and enter the DOS command window C:> Telnet 192.168.1.1 (Log in to ADSL831) Password: ADSL831 ( Enter a password, this is the default password) "PAT> AddPatin PPPoE XXX (port number required to map) such as 21,6881) / TCP 192.168.1.xxx (here you fill in the native intranet IP address set in front )> home "Save Save, will exit the connection, re-log in to the cat C:> Telnet 192.168.1.1 (Log in to ADSL831) Password: ADSL831 (Enter the password, this is the default password)" Restart (key step, must During OK, port mapping is completed. Do FTP, download with BT and no problem. The new ZTE blue vertical is different from this setting method completed in the web page. This method is limited to ZTE White Horizontal ADSL831.
EA700A port mapping
Like ZyXEL, and finally succeeded try to share with you the Getting Started Advanced Management 1. General Setup 21. Filter Set Configuration 3. Ethernet Setup 22. SNMP Configuration 4. Internet Access Setup 23. System Password 24. System Maintenance 25. IP Routing Policy Setup Advanced Applications 11. Remote Node Setup 12. STATIC ROUTING SETUP 15. SUA Server Setup 99. EXIT enters Menu 11.1 - Remote Node Profile
Rem node name = change = ip Active = yes bridge = no
Encapsulation = pppoe edit ppp options = no multiplexing = llc-based Rem IP addr = 0.0.0.0 incoming: edit ip / ipx / bridge = no rem login = trans password = ******* OUTGOING: session options: My Login = CZZ7205800 @ adsl edit filter set = no password = ******** PPPOE Idle Idle Timeout (sec) = 0 Authen = chap / PAP PPPOE Service Name = Schedule Sets =
Press Enter to confirm or esc to cancel: Note After the Edit Filter Sets = NO Space Bo is changed to YES, enter the following menu:
Menu 11.5 - Remote Node Filter
Input filter sets: protocol filters = 6 device file file = output filter sets: protocol filter sets: protocol filter sets: protocol filter sets: protocol filters = device filter filter file =
Enter Here to Confirm or Esc to Cancel:
The 6 space bar will be removed after the return storage is returned to the Edit Filter sets = no, do not take it, return the board after entering the market 15
Menu 15 - SUA Server Setup
Port # ip address -------------------- 1.Default 192.168.1.2 (map all ports to this machine) 2. 0 0.0.0 3. 0 0.0.0.0 4. 0 0.0.0.0 5. 0 0.0.0.0 6. 0 0.0.0.0 7. 0 0.0.0.0 8. 0 0.0.0.0
Press Enter to confirm or esc to cancel The first item is all ports, if 192.168.1.3 is made for FTP servers (port 21), 192.168.1.4 to do WED servers (port 80)
