Today, install the SATA hard drive in Redhat AS 3.2, and it's big! Very strange, install Windows2000, can find two hard drives correctly, and there is no problem. Install the red flag Linux, you can also recognize them correctly, nor did you find any questions. Partially biased under RedHat AS 3.2, there is always a problem. Search has gone through the whole google, nor did any result. Preliminary estimation is the problem of the kernel, but the same operating system version, the same SATA array card, the same hard disk configuration, the following, the next SERVER is going well! So I still think is a bit of a relationship with the motherboard chip! Anyway, didn't get it! Depressed first ....
Dmesg: ================================================= ================================================== BM-DMA AT 0x1400-0X1407, BIOS settings: hde: DMA, hdf:. pioHPT372N support is EXPERIMENTAL ONLY ide3: BM-DMA at 0x1408-0x140f, BIOS settings: hdg: DMA, hdh: pioSvrWks OSB4: IDE controller at PCI slot 00: 0f.1PCI: Enabling device 00 : 0f.1 (0000 -> 0001) SVRWKS OSB4: Chipset Revision 0svrwks OSB4: NOT 100% Native Mode: Will Probe Irqs Later IDE0: BM-DMA AT 0x1840-0X1847, BIOS Settings: HDA: Pio, HDB: Pio IDE1: BM-DMA AT 0x1848-0X184F, BIOS settings: HDC: Pio, HDD: PioHDC: Toshiba CD-ROM XM-7002BC, ATAPI CD / DVD-ROM DriveHde: MAXTOR 6Y200M0, ATA DISK DRIVEBLK: Queue C0502110, I / O LIMIT 4095MB (mask 0xffffffff) hdg: Maxtor 6Y200M0, ATA DISK driveblk: queue c05025f8, I / O limit 4095Mb (mask 0xffffffff) ide1 at 0x170-0x177,0x376 on irq 15ide2 at 0x1868-0x186f, 0x185e on irq 24ide3 at 0x1860-0x1867,0x185a ON IRQ 24HDE: Attached IDE-Disk Driver.hde: host protected area => 1HDE: 398297088 SECTORS (203928 MB) W / 7936KIB Cache, CHS = 24792/255/63, UDMA (33) HDG: attached ide-disk driver.hdg: host protected area => 1HDG: 398297088 SECTORS (203928 MB) W / 7936KIB Cache, CHS = 24792/255 / 63, UDMA (33) IDE-FLOPPY Driver 0.99.NewidePartition CHECK: HDE: hde1 hdg: hdg: status error: status = 0x00 {} HDG: Drive NOTY for CommandHDG: status error: status = 0x00 {}
HDG: Drive Not Ready for CommandHDG: status error: status = 0x00 {} HDG: Drive Not Ready for CommandHDG: status error: status = 0x00 {}
HDG: DMA DisabledHDG: Drive Not Ready for Commandide3: Reset: Master: Error (0x00?) HDG: status error: status = 0x00 {}
HDG: Drive Not Ready for CommandHDG: status error: status = 0x00 {}
HDG: Drive Not Ready for CommandHDG: status error: status = 0x00 {}
HDG: Drive Not Ready for CommandHDG: status error: status = 0x00 {}
HDG: Drive Not Ready for Commandide3: Reset: Master: Error (0x00?) End_Request: I / O Error, DEV 22:00 (HDG), Sector 0nd_Request: I / O Error, DEV 22:00 (HDG), Sector 2END_REQUEST : I / O Error, DEV 22:00 (HDG), Sector 4END_REQUEST: I / O Error, DEV 22:00 (HDG), Sector 6nd_Request: I / O Error, DEV 22:00 (HDG), Sector 0nd_Request: i / O Error, DEV 22:00 (HDG), Sector 2nd_Request: I / O Error, DEV 22:00 (HDG), Sector 4END_REQUEST: I / O Error, DEV 22:00 (HDG), Sector 6 Unable to read partition tableide-floppy driver 0.99.newidemd: md driver 0.90.0 MAX_MD_DEVS = 256, MD_SB_DISKS = 27md: autodetecting RAID arrays.md: autorun ... md: ... autorun DONE.pci_hotplug: PCI Hot Plug PCI Core version: 0.5Initializing Cryptographic APINET4: Linux TCP / IP 1.0 for NET4.0IP: routing cache hash table of 16384 buckets, 128KbytesTCP: Hash tables configured (established 524288 bind 65536) Linux IP multicast router 0.06 plus PIM-SMInitializing IPsec netlink socketNET4: Unix domain sockets 1.0 / SMP for Linux Net4.0.ramdisk: CoMP RESSED Image Found At Block 0
