Source: http://product.pchome.net/2004/07/16/744.php
Cute cool 2004-07-16
Regarding the hard drive with "illness", using the most traditional hard disk repair software. I tried a lot of software, and finally leaving only HDDREG, MHDD, FBDisk, and some original DM tools in my machine, as for MS ScanDisk, not to say. When the author starts to repair the hard drive, what software is often used in a mess, and the result is often made of hard drives even the original DM tools and even BIOS do not recognize. Now I have received a hard drive that I want to repair will definitely confirm that two things are not important, and the second is that BIOS can recognize. If the data is worth money than the hard disk, I will let the user spend money to find a professional; if BIOS doesn't recognize the hard drive, I can't help. Then go online, find information on models (causes for failure, processing methods, original tools). Finally began to start. The process I deal with is: First, first use the original tool, such as DM, etc., "Clear", "low", etc. This is the following benefits: First, after all, the original tool is safer. The second is that the small problem DM may solve, and the third is that some hard disk repair software will make the hard disk to even the original tool. I don't recognize the original. The factory tool is too late. The hard disk repair time will be greatly shortened by other software after the above treatment. Because some software, viruses or signs of the hard disk in some parts of the hard disk are derived from the abnormal switching machine, when these bad clusters are connected to one piece, they can use other software to handle it, it may exceed your imagination. I have encountered a hard disk, and there is a bad cluster of about 10MB. There are hundreds of bad clusters, and HDDREG, MHDD will handle hundreds, do you have to spend more time? After using DM, I will repair it with other software. This area will never see the bad cluster. The entire hard drive is only hundreds, and it is much faster. Second, use the repair software. HDDREG, MHDD, FB are very good, it is also very easy. HDDREG is getting troublesome, I use 131 version, it is to be installed on the hard disk. Download from some websites, you will let you download a new installer to the official website, then make a floppy disk after installation, then you can use it to fix the hard drive. It is best to copy several floppy disks because the floppy will read and write, if the bad clusters, the number of floppy reads will increase, it is easy to get the floppy disk. The software can be used under Windows and DOS, you can also determine from the first MB to start processing, but you can't decide where to end. MHDD, FB can be used directly, but can only be used under DOS. You can also bring them both COPY to the floppy disk, and a total of hundreds of KB. In terms of use, FB, HDDREG is easy to use, start them, will list the hard drives in the computer, you only need to select the hard drive to be repaired and then automatically complete. FB will automatically hide your hard disk bad, it will be a good partition, but you will pick up 4 largest to you, ask if you agree, you choose "Y", it is equivalent to fdisk once, but Restart your computer to format it. (Note: When the hard disk bad pass is more than scattered, your hard disk capacity will lose a lot, I tried it directly to repair a 2.5GB and a 4.3GB hard disk, and the result is only 1.8GB available, one is only 800MB available. The use of MHDD is a bit annoying, but the function is most. When you start, you will first list some parameter commands, then wait for you to enter the command. Pressing the F2 key is a hard disk setting, pressing the F4 button is the parameter setting interface, the default is all OFF, that is, only scanning is not repaired, the speed is faster. You can also set where to start from where to end.
Parameters generally put REMAP (bad track maps) and loop the test / repair (loop / fix, once again, until you call!) You can set it to ON, then press the F4 button to start working. You can also press the keyboard to faster or back. When it works, there will be a schematic diagram of Scandisk on MS to see you, it is very intuitive, so that you can have a number of quality on the hard drive. Before using these software, you must first turn the BIOS's virus function and hard drive write protection. FB will damage the data, MHDD and HDDREG will only damage the data in the bad area. They will also "fight" between them. This is OK, that is wrong. It is hard to say which software above is best. Software repair hard drives have taken long, three or two hours. If the hard disk is less important and the hard drive bad road is more, I will start the software at night, then turn off the monitor, go to bed, I wake up tomorrow morning. If you don't have a hard disk to ring a few hours, you can quit each time (you can press the "Ctrl Break" combination button for each time, but if you have not completed, you will report it. Scan, you can quit by X-button), remember the location, shut down, let it rest for ten minutes, then continue to repair, today, you can't finish it tomorrow (but FB seems to have no function) . If you feel unsatisfactory with FB partition, you can use Diskgenius or PQ, but if you use DG, you will be too annoying, PQ will also report the hard disk. If the capacity is not large, it is still a good time. Attachment: 1. Workflow: Ordinary hard drive: DM (cleaning, low) → FB, if the available capacity exceeds 50%, it is completed, otherwise: DM → HDDREG → MHDD → FB. HDDREG, MHDD is started before going to bed, wake up "receiving". Important hard drive: DM → HDDREG → MHDD → FB. It is best to take off a break at HDDREG and MHDD. 2. Software Download: Search on Baidu.com will have a lot of heap.