WINDOWS illegal operation details

zhaozj2021-02-16  120

The comrades here must have used Windows, and they must have experienced "illegal operation". There are two options in the "illegal operation" of one bar: "Close" and "Details". However, most people inside "Details" do not understand, but the grass is closed.

1. Stop error number: 0x0000000A

To explain the specific meaning of each detailed information of illegal operations. Description text: Irql-not-Less-OR-Equal

Usually: The driver uses an incorrect memory address.

Workaround: If you cannot log in, restart your computer. When you use the available system list, press the F8 key. On the Windows Advanced Options Menu screen, select "The last correct configuration", then press Enter.

Check if all new hardware or software is installed correctly. If this is a new installation, contact the manufacturer of hardware or software to get any Windows updates or drivers that may be needed.

Run all system diagnostic software provided by computer manufacturers, especially memory checks.

Disable or remove newly installed hardware (RAM, adapter, hard disk, modem, etc.), drivers or software.

Make sure the hardware device drivers and system BIOS are the latest version.

Make sure that manufacturers can help you have the latest version, or help you get these hardware.

Disable the BIOS memory option, such as cache or shadow.

2. Stop error number: 0x0000001E

Description text: kmode-esption-not-handled

Usually: The kernel mode process attempts to perform an illegal or unknown processor instruction.

Workaround: Make sure there is enough space, especially when performing a new installation.

If the stop error message indicates a particular driver, it is disabled. If the computer cannot be started. It should be started with the security mode to delete or disable the driver.

If there is a video driver that is non-Microsoft support, try to switch to a standard VGA driver or the appropriate driver provided by Windows.

Disable all newly installed drivers.

Make sure there is the latest version of the system BIOS. Hardware manufacturers can help determine if you have the latest version, or help you get him.

BIOS memory option, such as cache, shadow.

3. Stop error number: 0x00000023 or 0x00000024

Description text: FAT-file-system or MTFS-FILE-SYSTEM

Usually, the problem appears in NTFS.SYS (allowing the system to read and write the driver file of the NTFS drive).

Workaround: Run system diagnostic software provided by computer manufacturers, especially hardware diagnostics software.

Disable or uninstall all anti-virus software, disk defragmentation, or backup programs.

Check if the hard drive is corrupt by running the chkdsk / f command at the command prompt, then restart your computer.

4. Stop number: 0x0000002E

Description text: Data-Bus-Error

Usually: The system memory parity error is usually caused by hardware problems.

Workaround: Remove all newly installed hardware (RAM. Adapters. Hard Disk. Modem, etc.).

Running system diagnostic software provided by computer manufacturers, especially hardware diagnostics software.

Make sure the hardware device drivers and system BIOS are the latest version.

Use the system diagnostics provided by the hardware vendor to run memory checks to find failed or mismatched memory.

Disable the BIOS memory option, such as cache or shadow.

When starting, you can use the system list, press F8. On the Windows Advanced Options Menu screen, select "Start VGA mode:. Then press Enter key. If this does not solve the problem, you may need to replace different video adapters List, relevant supported video adapter lists, see Hardware Compatibility List.

4. Stop number: 0x0000002E

Description text: Data-Bus-Error

Usually: The system memory parity error is usually caused by hardware problems.

Workaround: Remove all newly installed hardware (RAM. Adapters. Hard Disk. Modem, etc.).

Running system diagnostic software provided by computer manufacturers, especially hardware diagnostics software.

Make sure the hardware device drivers and system BIOS are the latest version.

Use the system diagnostics provided by the hardware vendor to run memory checks to find failed or mismatched memory.

Disable the BIOS memory option, such as cache or shadow.

When starting, you can use the system list, press F8. On the Windows Advanced Options Menu screen, select "Start VGA mode:. Then press Enter key. If this does not solve the problem, you may need to replace different video adapters List, relevant supported video adapter lists, see Hardware Compatibility List. 6: Stop Error No .: 0x00000058

Description text: ftdisk-infrinkle

Usually: A main drive in a fault-tolerant set fails.

Workaround: Use the Windows Installation Disk to boot from the mirror (2) system drive. For the guidance of how to edit the boot.ini file to point to the mirror system drive, you can search "Edit ARC PATH" in the Microsoft Support service Web site. .

7. Stop error number: 0x0000007B

Description text: Inaccessi-Ble-boot-device

Usually: Initialization I / O system (usually refers to boot device or file system) failed.

Workaround: Guide sector viruses usually cause this stop error. It is the latest version of anti-virus software. Check if there is a virus on the computer. If the virus is found, you must perform the necessary not to find him from the computer. Please refer to the anti-virus software documentation to learn how to perform these steps.

Remove all newly installed hardware (RAM, adapter, modem, etc.).

Check the Microsoft hardware compatibility list to ensure that all hardware and drivers are compatible with Windows.

If the SCSI adapter is used, you can remove the latest Windows driver from the hardware provider, disable the SCSI device's synchronous negotiation, check whether the SCSI chain is ended, and checks the SCSI ID of these devices, if you are unable to perform these steps, Refer to the document of the hardware device.

If you use an IDE device, define the IDE port on the board as a unique main port. Check all the IDE devices from the IDE device. Remove all IDE devices outside of your hard disk. If you can't confirm how to do this? Find, refer to the hardware document.

If the computer has formatted using the NTFS file system, restart your computer and then run the Chkdsk / F / R command on the system partition. If you cannot start the system due to an error, use the Command Console and run the Chkdsk / r command.

Run the chkdsk / f command to determine if the file system is corrupted. If Windows cannot run the chkdsk command, move the drive to other running Windows, then run the CHKDSK command to the drive from this computer.

7. Stop error number: 0x0000007B

Description text: Inaccessi-Ble-boot-device

Usually: Initialization I / O system (usually refers to boot device or file system) failed.

Workaround: Guide sector viruses usually cause this stop error. It is the latest version of anti-virus software. Check if there is a virus on the computer. If the virus is found, you must perform the necessary not to find him from the computer. Please refer to the anti-virus software documentation to learn how to perform these steps.

Remove all newly installed hardware (RAM, adapter, modem, etc.).

Check the Microsoft hardware compatibility list to ensure that all hardware and drivers are compatible with Windows.

If the SCSI adapter is used, you can remove the latest Windows driver from the hardware provider, disable the SCSI device's synchronous negotiation, check whether the SCSI chain is ended, and checks the SCSI ID of these devices, if you are unable to perform these steps, Refer to the document of the hardware device.

If you use an IDE device, define the IDE port on the board as a unique main port. Check all the IDE devices from the IDE device. Remove all IDE devices outside of your hard disk. If you can't confirm how to do this? Find, refer to the hardware document.

If the computer has formatted using the NTFS file system, restart your computer and then run the Chkdsk / F / R command on the system partition. If you cannot start the system due to an error, use the Command Console and run the Chkdsk / r command.

Run the chkdsk / f command to determine if the file system is corrupted. If Windows cannot run the chkdsk command, move the drive to other running Windows, then run the CHKDSK command to the drive from this computer.

7. Stop error number: 0x0000007B

Description text: Inaccessi-Ble-boot-device

Usually: Initialization I / O system (usually refers to boot device or file system) failed.

Workaround: Guide sector viruses usually cause this stop error. It is the latest version of anti-virus software. Check if there is a virus on the computer. If the virus is found, you must perform the necessary not to find him from the computer. Please refer to the anti-virus software documentation to learn how to perform these steps. Remove all newly installed hardware (RAM, adapter, modem, etc.).

Check the Microsoft hardware compatibility list to ensure that all hardware and drivers are compatible with Windows.

If the SCSI adapter is used, you can remove the latest Windows driver from the hardware provider, disable the SCSI device's synchronous negotiation, check whether the SCSI chain is ended, and checks the SCSI ID of these devices, if you are unable to perform these steps, Refer to the document of the hardware device.

If you use an IDE device, define the IDE port on the board as a unique main port. Check all the IDE devices from the IDE device. Remove all IDE devices outside of your hard disk. If you can't confirm how to do this? Find, refer to the hardware document.

If the computer has formatted using the NTFS file system, restart your computer and then run the Chkdsk / F / R command on the system partition. If you cannot start the system due to an error, use the Command Console and run the Chkdsk / r command.

Run the chkdsk / f command to determine if the file system is corrupted. If Windows cannot run the chkdsk command, move the drive to other running Windows, then run the CHKDSK command to the drive from this computer.

10. Stop error number: 0x00000077

Description text: kernel-stel-stack-INPAGE-ERROR

Usually: Unable to read the page required by the kernel data from the paging file to memory.

Workaround: Use the latest version of the anti-virus software to check if there is a virus on the computer. If the virus is found, the necessary steps will be made to clear him from the computer. See all system diagnostics software provided by the manufacturer, especially memory checks.

Disable the BIOS memory option, such as cache, shadow.

11. Stop error number: 0x00000079

Description text: mismatched-hal

Usually: The hardware abstraction layer does not match the kernel or machine type (usually in the case where the single processor and multiprocessor configuration file are mixed in the same system).

Workaround: To resolve this error, use the command console to replace the wrong system file on your computer.

The kernel file of a single processor system is Ntoskml.exe, and the multiprocessor system's kernel file is ntkrnlmp.exe, but these files should correspond to the files on the installation media; in installation of Windows2000 and, no matter which Original files will be renamed NTOSKRNL.EXE files. The HAL file also uses the name HAL.DLL after installation, but in the installation of the media, but there are several possible HAL files on the installation media.

12. Stop error number: 0x0000007A

Description text: kernel-data-INPAGE-ERROR

Usually: Unable to read the page required by the kernel data from the paging file to memory. (It is usually due to faults, viruses, disk controllers, or by faulty RAM).

Workaround: Use the latest version of the anti-virus software to check if there is a virus on the computer. If you find a virus. If the necessary steps are required to clear him from the computer, see how to do these steps for the case of the case.

If your computer has formatted with NTFS file system. You can restart your computer and then run the chkdsk / f / r command on the system partition. If the command cannot be started due to an error, use the command console and run the chkdsk / r command.

All systems running by computer manufacturers are in very hardware, especially memory checks.

13. Stop error number: 0xc000021A

Description text: status-system-process-terminated

Usually: User mode subsystems, such as Winlogon, or Customer Server Runtime Subsystem (CSRSS) has been corrupted, so security is not guaranteed. Workaround: Remove all newly installed hardware.

If you cannot log in, restart your computer. Press F8 when an available system list appears. On the Windows2000 Advanced Options Menu screen, select: "The last correct configuration". Then press the car.

Run the fault recovery table and allow the system to fix any detected errors.

14. Stop error number: 0xc0000221

Description text: status-image-checkisu7m-mismatch

Usually: Drivers or system DLLs have been damaged.

Workaround: Run the fault completion table and allow the system to fix any detected errors.

If an error occurs immediately after the RAM is added to the computer, it may be damaged by paging files, or the new RAM is malfunctioned or incompatible. Delete PageFile.sys and returns the system to the original RAM configuration.

Run all system diagnostic software provided by computer manufacturers, especially memory checks

转载请注明原文地址:https://www.9cbs.com/read-13694.html

New Post(0)