Lilo.conf Interpretation and Self-start CD Making NULL NULL
〖
Back to〗 Forward〗
Q: redhat6.1: 1 Boot = / dev / sda 2 map = / boot / map 3 install = / boot / boot.b 4 prompt 5 timeout = 50 6 default = linux 7 image = / boot / vmlinuz 8 label = Linux 9 INitrd = / boot / initrd-2.2.12-20.img 10 read-only 11 root = / dev / sda1 now, what is the difference between (1) row 1 Boot and Row 11 ROOT? (2) Line What is MAP, INSTALL, and INITRD? 2, 3, 9? After compiling the new kernel, do you want to replace them? Who replaces? A: AT 04/11/00 05:05 PM, Scenter Wrote: root refers to the location of your root directory. Boot is the location of the startup, used for the floppy disk. You compile the new kernel and do this: Add the following line: image = / boot / vmlinuz-new label = kernel-new root = / dev / hda3 read-only where VMLinuz-New is the name of your newly compiled kernel, You have changed yourself. Then run Lilo. ============================================================================================================================================================================================================= ============= Q: I originally used the OS Loader of NT as a secondary guide, LILO as a leader, which first loaded WIN98, back Winnt, then loaded Linux, now I want to remove lilo, but I still keep Os Loader as a tool to guide Win98 and Winnt, I don't know how to use Win98's FDISK / MBR, if not, please guide the younger brother to do it. A: 1.boot you computer by dos boot Disk. 2.Run fdisk / mbr good luck ======================================== ======================= q: How to remove LILO Boot Loader? A: Please start with a DOS disk, run the fdisk / MBR to remove LILO.
============================================================================================================================================================================================================= ============== q: Hello, there is a problem, I have two hard drives, one 8.4G is the primary disk (all Win98), one 6.4g is from the plate (divided into Win98 and Linux two districts), I usually use one in CMOS to block one, I will install WIN98 and install the Win98 in front of the plate, the problem is: 1.Linux recognizes two hard drives, 2. After installing Linux (only starts from / dev / hdb2, select the primary disk start, my primary Win98 can not start), can not boot LILO, and Win98 can not start, but can be launched with Liunx first aid floppy disk. Request a rescue approach. Thank you, I recommend using the SmartFDisk written by Tsinghua Ph.D. Suzhe to solve this situation. I have experimented, there is no problem. Win98 is located in / dev / hda. SmartFDisk can go to http: //suzhe.home .chinaren.net or other places download is a very good free software. 16 bits are Shareware, 32-bit GPL. Now is V2.0, the next semester can go to V3.0 version. Used compiler It is a GCC transplanary version of DJGPP, M $ platform. SmartFDisk currently supports partitions of the FAT system, multi-system boot. Future versions will be integrated into PQ, SysCommander, and other partitions and other partitions and guides, and provide GNU / Linux version. == ============================================================================================================================================================================================================= ============= q: My LILO is full of 00 00 00 00 00 00 00- .... Do not stop, start rewriting LILO when using CD, warned to Exceed 1024 Cylinder Limit, The fault is still.
My hard disk is 8.4g, a total of 1027 cylinder, there are two 1G partition in front of the Linux root partition, how can this be? A: Linux's boot directory must be located within the first 8G of the hard disk. Otherwise, Linux does not recognize you to partition the partition of your partition to install Linux / boot to the first 8G Good Luck A: Actually, the problem is the reason: for the hard disk There are two different forms: 1. Boot the system, the addressing of the hard disk is booted according to the hard disk parameters stored in the CMOS; CYLS, Heads, SECS; Cylinder occupies 10 binary positions, addressing only It can be 0 - 1023; this is the Linux system that cannot be used in 1024 cylinders that cannot be used by LILO. 2. When installing the linear address space, select the linear mode, and give it a hard disk parameter. You can take a look at the BIOS settings The hard disk parameters correspond to the line of the LBA mode, such as the parameters of the HDA = 1869, 63, 255 IBM 15.2G hard drive. Edit /etc/lilo.conf, after the LINEAR mode is added to the following format: Boot = / dev / hda map = / boot / map install = /boot/boot.b prompt linear: -} add this timeout = 50 image = / boot / vmlinuz label = linux root = / dev / hda1 initrd = /boot/initrd-2.2.12-20.img Read -only append = "HDA = 1869, 63, 255": -} add this modification, save, play the lilo command at the command prompt, when the Linux system is started again, LILO will boot the system according to the linear mode. == ============================================================================================================================================================================================================= ============= Q: How to do Linux boot CD A: I just made it last month, remember to be like this: # mkisofs -r -l -t -b. ./Images/ Boot.img -c ../IMages/boot.cat -o myself.iso / mnt / cdrom then start to DOS / Windows, you can engrave with Easy_CDPRO (select CD Mirror) You may need MAN Mkisofs, pay attention to -B And -c usage, use your own boot.img instead of the above value, as for the boot.cat file, but it is an indispensable participation Number, it seems that there is no use, you can just find a commendation. If your boot.img is an img that can automatically enter the installation mode, then you have made a disc installed CD !! Note, Do you have a number of machines that you can test itself, you are unfortunately, I am unfortunately, I can't start the machine started from the CD-ROM. I'm re-engraving it (^% * & (* &) == =====================================
