Toner cartridge uses small common sense
Problems should be paid attention to when using the toner cartridge
In order to ensure the normal task of the toner cartridge you purchased, we offer the following recommendations for your reference: Laser printers, it is best to place it under the air-conditioned environment to achieve the best printing effect and reduce the failure rate. Please put the toner cartridge in the corresponding laser printer in the correct direction. Do not open the toner cartridge hood and the surface of the touch photosensitive drum. Do not turn the photosensitive drum.
Several phenomena that are often present
Toner drum leakage: In addition to the housing damage, it is usually the cause of the magnetic stick powder in the toner cartridge during transportation or during the use of certain customers. The solution is simple, just turn a few laps in the direction of the drum. * Print files and drum cores appear simultaneously
1
cm
The same wider longitudinal black, general customers also think that it is a leak powder: This is a problem with the scraper, causing the powder on the stick. * Various longitudinally appearing on the print file: It is usually a small blade on the edge of the scraper and the squeezing on the edge of the blade. * The landscape in the print file: It is usually a magnetic stick in the toner cartridge, and it is possible to turn a few laps. * If there is a significant bottom ash on the print file: is usually a problem of drum or carbon. * Print file color is uncomfortable, famous white road: Can you see carbon powder from the outside, if you see some places on the magnetic stick, there is no powder, and there is no powder, indicating that this toner cartrin is exhausted. * If the printer bears white paper: Check if the printer is problematic, if there is no problem, then the toner cartridge has a problem in assembly. * In addition to the above problems, the printer can usually be considered a problem.
Toner cartridge regeneration filling powder and its benefits
The regenerative filling powder technology of the toner cartridge is to use the original selenium and then fill the toner after using the original selenium. This technology comes from the United States. Americans believe that: <1>, the original toner cartridge can be completely regenerated after the first time. <2>, if it is not regenerated, the amount of discarded toner is large, causing a lot of pollution to the environment.
Use the qualified regenerative toner cartridge now, usually use regenerated toner cartridges in developed countries such as Europe. Our company implements the toner cartridge regeneration filling powder has been many years. After the exploration and in-depth study of these years, the regeneration technology is already mature. At the same time, we have been fully understood by the benefits of regeneration of the toner cartridge. <1> After the carbon powder is used, the main fittings in the toner cartridge are in a good condition, and the charging roller is in a good state, and the technical treatment is used, and the special toner can be used. After the first filling, the main fitting performance of most of the toner cartridges can also be used, and the filling powder can be done again. (After the filling powder, it must be approved by our professionally. After the second regeneration filling powder, the drum in the toner cartridge can no longer be reused, while other accessories can be, After replacing the drum, the scraper is regenerated. Obviously, due to the use of 1 to 3 regeneration filling powder, the original toner cartridge has a minimum of 50% to 70%, (if the original consumption of 100 original toner cartridge now only consumes 30 ~ 40) directly, saving it directly 30% of the cost of purchasing the original toner cartridge. <2> Practice has proved that after using our toner cartridge regeneration technology, it does not have any effect on the printing effect, and the number of toner cartridges after the filling powder regeneration is not lower than the original toner cartridge.
Laser print quality failure
White track traces are most likely that there is no ink powder. Take the toner cartridge, slightly swayed, then put it in the printer, if the printing effect is significantly improved, then the toner in the toner cartridge is not much; if it is confirmed that the toner is sufficient, there is a white track, then the problem should be serious, need Replace the toner cartridge. When printed continuous printing, the page that is lost in the content file is printing normally, but the back page will lose content or the text appear black or even all black or all white, and the paging print is normal. This is due to the relatively complicated information of the page description information of the file, causing the printer memory insufficient. You can reduce the printer's resolution to a grade implementation print, and the best solution is of course the memory of the printer. Printing the paper surface with dry cleaning soft cloth wipes the paper tract inside the printer to remove toner left in the paper road; print the three-page file for only one word per page, used to clean the components inside the printer; Quality of printing paper; if there is still a problem, it may be necessary to replace the carbon cartridge or toner cartridge. Print appears to be garbled printer self-test to determine if a hardware failure is present; detect the printer cable and connection (in the DOS command state, enter a directory of less than a file, type "Dir> PRN" and enter); Print the test page under Window to determine if the printer driver is installed correctly; check if the application itself has problems. After replacing the motherboard or the microcomputer may not print the parallel port type setting, you need to convert between the standard print port and the ECP print port. You can make changes in the BIOS setting, or you can change the driver "→" Drivers "→" Properties → "Driver" → "Properties →" Driver "→" Properties → "Driver" → " Displaying all devices, interchange "ECP Print Port" and "Printer Port". Toner kid
The mounting of the toner cartridge for the mounting of the drum, first take the toner cartridge from the package and extract the sealing strip. Note It must be completely drawn out of the sealing strip, and the case where there is no sealing strip and cannot be printed. Then the axis of the toner cartridge is axis rotation, so that the drum powder is uniform in the toner cartridge, so that the print quality is improved. Second, a parallel white line is generally because there is not much toner in the toner cartridge. You can take the toner cartridge, sway left and right, then put it in the machine, such as printing, indicating that there is not much toner in the toner cartridge; if there is a white line, there is a need to replace the new toner cartridge. Third, the method of handling paper jam is very common. When the paper is placed, the paper is splable, and the paper sheet is tightly tightened, and the paper jam can be effectively avoided. Don't worry when jams. First open the printer flip, remove the toner cartridge, pull the green switch on the left side of the printer upward, which can expand the gap of the roll. Use your hands to gently pull the stuck paper. At this time, pay attention not to force, pull the paper.
The toner cartridge of the laser printer of the toner cartridge is the organic silicon light conductor. There is a working fatigue problem. Therefore, the continuous working time is not too long. If the output is large, you can stop going to take a while for a while, continue to output. Some users use two powder boxes to alternately work, and it is also a way. As for the maintenance and maintenance of the toner cartridge, it can generally be carried out: (1) Carefully remove the toner cartridge assembly, wipe the surface with a skim cotton, but it is not possible to prevent the toner cartridge surface. (2) Wipe the surface of the toner cartridge with a deprimatinous cotton toner cartridge. When wiping, a spiral scratched method should be taken. After polishing, immediately remove the cleaner with a degreasing cotton. (3) Use the gauze with talc to gently take a layer of talc powder on the surface of the drum to replace it. (4) It is usually noted when replacing the toner, cleans the waste powder in the waste powder collection, so as not to affect the output. Because the waste powder is stacked, the "leakage" phenomenon will appear, that is, an irregular black point, black block on the output (generally in portrait), if not eliminated, continue to use, for a while Severe bottom ash (and longitudinal scratches) will appear. The cause of this failure is that the first waste powder is full, so that the reproduction of the waste powder cannot enter the waste powder to create a warehouse, and the waste powder in the waste powder warehouse will continue to "squeeze" and produce "leakage powder". Then, since the waste powder contained in the dirt, the fibers, etc., the fiber is coarse, and the toner cartridge is rubbed for a long time, and it is getting tightening, the pressure is getting bigger and larger, and finally grinds the photosensitive film of the toner cartridge. The toner cartridge is it's broken. Therefore, the output paper sample ash is severe, since they have always been longitudinally friction, so longitudinal scratches can be seen in the bottom ash. Therefore, immediately clean the waste powder warehouse immediately when the output "leak powder" is found. Finally, it should be noted that the toner cartridge is cleaned to avoid light. Environmentally friendly toner cartridges use small knowledge
Installation environment: temperature 10
-330C
, Relative humidity 20-80%. 2, use the appropriate print media: Do not use the incision, tear, wrinkles, rolls, broken holes and staples of the staples; too thick paper (especially business card paper) will quickly grind the photosensitive Drums, as little as possible; when printing the film, some film coatings will dissolve bond on the fixing roller, resulting in a permanent damage, so pay special attention to the selection of the film. 3, when replacing the toner cartridge, it is best to place the powder box in the cleaning machine in the cleaning machine, use the paper-sack and toner accumulated on the paper, the exposed electrical contact piece can be wiped with a cotton swab to keep good electricity Contact. Otherwise, it may cause printing. 4, to check if the drum is flexible, only the photosensitive drum gear can be pushed in the direction pushed away from the drum cover for a week (
74A
versus
3903A
The opposite is true. If the user is inverted the photosensitive drum, the carbon powder can be stacked between the magnetic roller and the powder knife, causing a drain powder. 5, the toner cartridge is used to swing the powder cartridge 6-8 times, so that the carbon powder is loose and distributed uniform, then pull the seal out and put the toner cartridge into the printer. 6, in general, if the machine appears with Toner Low, the print will appear color-shallow phenomenon. At this time, you can shake the powder box, and you can print 40-50 sheets.
Toner filling
HP C
3900A
Toner cartridge (HP 4V / 4MV / 4VC) Canon EP-B toner cartridge (CANON LBP-BX) filling powder and cleaning method
The separation of the toner cartridge opened the machine to remove the toner cartridge on the table, first pick a spring on the toner cartridge, clamping a side metal pin with a sloppper, pull out to the external force, two sides of the silver metal pin can be divided into two Part of the drum core is a waste powder collection, with a magnetic roller is a powder warehouse. Replace the drum and scraper, remove the screws on the white plastic clips on the on-gray photosensitance drum on the wafer collector, pull out the white plastic card outward, the drum core can be taken. Take the discharge roller, remove the two screws on the blade to take out the scraper, clean all the waste powder, and then restore the squeegee, discharge roller, and the photosensitive drum (pay attention to the drum core and The white plastic clip and discharge roller in both ends cannot be reverse). Gently turn the drum number, and clean it on the drum. If there is a residual powder on the drum, the blade should be replaced in time. Filling toner If your toner cartridge is the original toner cartridge for the toner, the powder is not needed to clean the powder warehouse and the magnetic roll, otherwise the powder warehouse and the toner on the magnetic roller must be Clean it clean. Remove the plastic cover on the powder warehouse, shake the 4V / 4VC toner and slowly pour it into the powder warehouse, cover the plastic cover, gently turn the magnetic roller plug, and the magnetic roll should be uniformly adsorbed Assembling the toner cartridge, the powder warehouse and the waste powder collector are assembled to install recovery at the time of unpacking, plug in both sides of metal card pin. After the toner cartridge is installed, the photosensitive drum barrier should be pushed up, and the drum core side gear is turned back, and the drum-residue toner is removed, and the installation can be used. Watch the top: (1) When there is a regular black point on the paper, it is proved that the drum drum is damaged and should be replaced in time. (2) The additive powder should be high quality laser toner, otherwise print quality cannot be guaranteed.
HP C
3903F
Toner cartridge (5P / 5MP / 6P / 6MP) HP
92274A
Toner cartridge (HP
4L
/ 4ml / 4LC / 4P) Filling and cleaning method:
First, will
92274A
The toner cartridge is flat on the table, first extract the baffle (blocking the drum and can rotate on one side there in a spring), there is a deep hole on the outer casing side of the baffle spring, there is a small screw, put this small Screw is taken out (
3903F
The toner cartridge does not have this small screw). 2, turn the toner cartridge (write
92274A
Or c
3903F
On the side of the side, seeing four clams, look back to the right (that is, the end of the drum belt gear) There is a pair of clams, there is a kiss on both sides, take these clams slowly, the toner cartridge is It is divided into two parts, namely the supply part (there is a powder bin and discharge roller) and a single drum portion. Third, replace the single drum (no change in the core can save this): take out the pin or kicks on both ends of the drum, take the old single drum and replace the new single drum, and then put the pin or the kick, gently turn The drum core, the surface of the drum should be clean, and if the toner cannot be scraped off, the blade should be replaced. Fourth, first put the discharge roller on that part of the powder warehouse and a small tooth, clean the powder and waste powder clean, put the toner, and then put the discharge roller and the pinion back to the original position. 5. The relative position of the powder warehouse and the waste powder warehouse is restored to the original state (otherwise the toner cartridge will be lost in the original state (otherwise the toner cartridge will drain the powder). .
Note: 1. Be cautious when dismantling, do not break the card. 2, the additive powder should be pure laser toner, otherwise the toner cartridge usage is shortened, and the machine is contaminated.
HP C
3906F
(
5L
/
6L
/
6L
PRO /
6L
GORL) 3100 toner cartridges and cleaning methods:
First, turn on the machine to remove the toner cartridge, clamp the metal pin with the sloping pliers, pull out to the external force, and then divide the toner cartridge into two parts, with the drum core is a waste powder collection. A magnetic roller is a powder powder. Second, clean up waste powder: Put the metal positioning on both sides of the light blue photosensitive drum in the waste powder collection, take out the photosensitive drum in the dark, take out the discharge roller, and then put two nails on the blade Infinite, remove the scraper, slowly pour the waste powder in the waste powder, and then restore the scraper, discharge roller, and the photosensitive drum (if you need to replace the drum, the scraper will be the old drum at this time. The squeegee is replaced to a new one). Third, filling toner: Routing the nails on the magnetic roller on the powder powder, to take a plastic shell, see a purple plastic cover, open this cover, put the flour warehouse and the magnetic roller The toner is all cleaned up (if it does not clean up the magnetic roller and the powder warehouse print sample, the bottom ash or the writing is shallowed), and the magnetic roller is loaded. At this time, the application force holds the magnetic roller to prevent the magnetic roller from being separated from the original position. When the laser printer toner is shaken, then slowly pour it into the powder storage position, cover the plastic cover, on the plastic shell (at this time, pay attention to the semi-circular shape on the middle of the magnetic roller and the semi-circular small Hole is good), gently rotate the number of gears on the side of the magnetic roll to make the toner on the toner. IV, install the powder powder and the waste powder collectors to install recovery, plug in both sides of metal card sales. After the toner cartridge is installed, the photosensitive drum barrier should be pushed up, and the drum core side gear is turned back, and the drum-residue toner is removed, and the installation can be used. Note: (1) When there is a regular black point on the paper, it is proved that the photosensitive drum is damaged and should be replaced in time. (2) The additive powder should be a pure laser toner, otherwise the toner cartridge usage is shortened, and the machine is contaminated.
