Nokia mobile phone FAQ

xiaoxiao2021-03-06  23

First, * # 06 #: Display IMEI code

Second, * # 0000 #: Display software version

(Part of the model does not work, can press * # 号 Code #, such as * # 6110 #)

First line - software version;

Second line - software release date;

Third line - mobile phone model

Third, * # 92702689 #: Display serial number and IMEI code, with scrolling menu

The first screen representation - Mobile phone factory: 1197 (monthly month);

The second screen represents - serial number and IMEI;

Third screen representation - Purchase Time: 1197 (monthly month) can change once

(But you can't make changes again after input, the date will be permanently recorded)

The fourth screen represents - the last repair time: 0000 (Year of the month).

Fifth screen representation - Transport user data: Exit Turning the phone and returns.

If the above is not working properly, and the phone asks you to enter a legitimate code, try:

1) .6232 (ok): Show the month and year of manufactured

2) .7832 (ok): Show the month and year of mobile phone purchase time

3) .7332 (OK): Show the month and year of the recent maintenance time and the year: 0000 (Year of the month)

4) .9268 (ok): Show series number

5) .37832 (OK): Set the month and year of the purchase time (Warning: Only allowing it)

6) .87267 (ok): Confirm transfer, related to software updates

Fourth, rate coding

* 3370 # or * EFR #: Open (EFR) full rate encoding

# 3370 # or # EFR #: Close full rate coding

(Turn on full speed enhanced coding mode, improve voice quality but power consumption)

* 4720 # or * HRA0 #: Open (HR) semi-rate encoding

# 4720 # or # HRA0 #: Close half rate coding

(The voice quality is lowered, but the battery can be extended by about 30%, and the network is required.

When you type these code, you will turn off and then you can take effect.

V. SIM lock information

* # 746025625 # (= * # SIM0CLOCK #): If the SIM card can be locked, type the instruction when it is detected, the phone displays / "sim clock stopted /" or "sim clock stock not allowed /", this depends Your SIM card.

SIM card lock information: including four different locks

1). National lock-lock designated country

2). Network lock - lock designated network

3). Suppliers lock-lock service provider

4). SIM card lock - lock specified SIM card

6. Query if the phone is locked

First, you must find several keys that must be used when setting your phone. Among them, press / " /" in succession of the * button; continuously press the * button three times, then / "p /"; continuously press the * button four times, "W /" will appear. You can then enter the corresponding combination key in turn.

# pw 1234567890 1 #: Query if the lock country code

# pw 1234567890 2 #: Query if the lock network code

# pw 1234567890 3 #: Query if the lock network provider locks the code

# pw 1234567890 4 #: Query if the lock SIM card

7. Power button

Touch the power button, the screen will display the Sands Mode, you can switch to each mode with the upper and lower keys. Open the screen light in the keyboard lock mode, have you experienced the troubles of the keyboard lock that wanted to open a mobile phone at night? In fact, you can touch the power button. At this time, the nightlight of the screen and the keyboard will open so you can distinguish the button to open the keyboard lock. Eight, check the phone status

Operational instruction: #P (Mastercode) x #

(Mastercode) is a 10-digit (no parentheses) x is a number of 1 to 4, it shows the above lock, and is not sure that the number is corresponding to the lock.

The SIM card does not limit the information, meaning that your phone has not been locked.

1) .vin Charger INPUT VOLTAGE 8.4V 0.8A

2) .chrg Ctrl Charger Control PWM 32kHz

3) .XMIC MIC INPUT 60MV - 1V

4) .SGND SIGNAL GROUND

5) .XEAR EAR OUTPUT 80MV - 1V

6) .mbus 9600 b / s

7) .fbus_rx 9.6 - 230.4 kb / s

8) .fbus_tx 9.6 - 230.4 kb / s

9) .l_gnd charger / logic gnd

Nine, Nokia 9000 / 9000i

1) Show IMEI: * # 06 #

2). Display software version number: * # 682371158412125 # Latest version under Phone Information

3). Show manufacturing weeks and year: * # 3283 #

4). Phone type: GE8

Ten, 5110 latch code machine decoding

Steps: Press C, Press -> Press C Do not put -> Press * Do not put -> Press * Do not put ->

Type 04 * Pin * Pin * Pin #, is completed.

Eleven, replace the current number

Press and hold the # key does not let a second clock, the screen will appear "exchange number?", One 2 words will appear on the screen after confirmation, then the phone cannot all dial, but can answer the call. Remove the weight once, use it to achieve the effect of the lock. When you enter the call menu, you will continue to press and hold the function key for two seconds, and you will enter the call menu, and this menu usually only occurs when there is a call.

Twelve, 6110 display name in standby screen

Choose a least frequently used mode of operation, usually the pager Menu3-5, after setting the personalization of Menu3-5-2, rename Menu3-5-3 to your name, after startup. Remarks: To restore to the pager, rename Menu3-5-3 is blank.

转载请注明原文地址:https://www.9cbs.com/read-42270.html

New Post(0)