Win2000 may be able to be a syndicable operating system, but it still does not avoid Blue Screen of Death issues. The purpose of this article is to solve the problem of BSOD, and give a solution to the general blue screen problem. Introduction What is a blue screen crash (BSOD) problem? BSOD is an error message displayed in a blue screen background. Generally, this error message is serious to your entire operating system, and you only have a selection of reincolution. Stop messages and hardware messages Win2000's BSOD and NT4 previous BSOD messages are completely different. The biggest difference is that the BSOD in the NT contains only one universal stop message type (that is, the actual error code), but the Win2000's BSOD contains two message types: stop messages and hardware messages. The stop message refers to the error message generated when the Win2000's kernel finds a software error it cannot recover. The hardware message refers to the error message generated when Win2000 found a serious hardware conflict. The BSOD BSOD can be divided into a separate portion, and each part contains valuable error handling information. These parts include: 1, bug check section: This is where the BSOD contains the location of the actual error message. In this section, you should pay attention to the error code (that is, hexadecimal numbers behind the word "stop") and error symbols (that is, the words followed after the error code) 2, recommend users to take action part: this Some frequent messages that often contain some general guides you correct the incorrect steps. 3, debug port information section: This part contains information you should set your kernel debugger. The kernel debugger is a tool that allows you to connect to your computer and debug the process. Four types of stop messages When the program or the driver has an error message that cannot be controlled or attempts to execute an illegal instruction, the system will stop the error message. This information is usually consisting of four types. 1. General Stop Message: Stop Message that occurs when using WIN2000, Install Stop Message: Stop messages in the Win2000 process are installed, usually caused by the existence and 2000 incompatible hardware devices in your system. 3. Executable Program Installation Stop Message: Indicates the stop message of the 4th phase (executable program part) during the 2000 installation process. 4. Software Trap Stop Message: Due to the error traps in the software and the stop message that occurs when the program tries to execute an illegal instruction. Regardless of whether Win2000 has so far the greatest operating system or not, it is not wrong. At least we know that in 2000, BSOD still exists.
The following is a more detailed description of it: The following is a specific example of BSOD:; *** Stop: 0x0000001E (0xF24A447A, 0X00000001, 0X0000000) KMODE_EXCEPTION_NOT_HANDLED *** Address F24A447A base at f24A0000, DateStamp 35825ef8d - wdmaud.sys If this is the first time you've seen this Stop error screen, restart your computer If this screen appears again, follow these steps:.. Check to be sure you have adequate disk space If a driver is identified in the Stop message, disable the driver or check with the manufacturer for driver updates. Try changing video adapters. Check with your hardware vendor for any BIOS updates. disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable components, restart your computer , Press F8 TO SELECT Advanced Startup Options, And The Select Safe Mode. Refer to Your Getting Started Manual for More Information On Troubleshooting Stop Erro 2 (Port 0x2F8, B AUD RAT 19200) Beginning Dump of Physical Memory Physical Memory Dump Complete. Contact Your System Administrator Or Technical Support Group. According to this specific example, follow the BSOD of the above, the following introduction: BUG check section: This is The BSOD contains the location of the actual error message. It looked like the following code: *** Stop: 0x0000001E (0xF24A447A, 0X00000001, 0X0000000) KMODE_EXCEPTION_NOT_HANDLED *** A ddress F24A447A base at f24A0000, DateStamp 35825ef8d - wdmaud.sys error code which is followed by a ten on the back of Stop The six-incoming number, which consists of other four numbers. The error symbol refers to the Kmode_Exception_Not_Handled next to it. In some BSOD error information, a memory location and file name appear behind the error symbol. This information tells the occurrence of errors when the location and which files in the memory occur when the error occurs. Of course, can you see which stop message type is determined by this information. In some practical use, you can only see the first line above. Here, it is usually meant to represent problems caused by the display service.
Recommended users take action part: Recommended users in the above examples as follows: if this is the first time You've Seen this stop error screen, restart Your Computer. If this Screen Appers Again, FOLLOW TO BE STES: Check To BE sure you have adequate disk space. If a driver is identified in the Stop message, disable the driver or check with the manufacturer for driver updates. Try changing video adapters. Check with your hardware vendor for any BIOS updates. disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Refer to your Getting Started manual for more information on troubleshooting Stop errors. recommended The user takes a moving portion is usually recommended that users should take the solution after the error message is encountered. As can be seen in the message, solving a BSOD may be resolved as long as you restart or organize enough surplus space. Although this method occasionally plays, it is actually a much more complicated to Solve BSOD. Debug port information section: This section contains information you should set your kernel debugger. I will introduce what is 2000 kernel pricklers in the future website. In the example above, this section is: Kernel Debugger Using:. COM2 (Port 0x2f8, Baud Rate 19200) Beginning dump of physical memory Physical memory dump complete Contact your system administrator or technical support group of four types of conventional stop stop information Message: Regular stop messages are often the hardest error message because there may be countless reasons can result in errors. Install Stop Message: Stop messages in the Win2000 process are installed, usually there is a device in your system in the 2000 hardware compatible list. The solution is to view the hardware device in the system and find the device that is not listed in the 2000 compatible list. Then contact your hardware device manufacturer to see if they can provide you with the driver of the device. If they can't, then you have to delete the device from your system and replace it with other compatible devices. If your hardware is compatible, you may have two hardware devices with two mutually conflict. To solve this problem, remove any hardware devices that are not necessary, then reload 2000, once the 2000 loading is successful, all removed all removed devices all re-entered into the system. Doing so, you usually solve this problem, at least you can tell you which hardware is conflict.
