Epson
Color spraying and
HP
Clearness of the laser counter
Epson
The model is divided into the following types:
1
.
480
,
580
,
C20
,
C40
,
C41
series
When the unknown error is displayed when the service request, the service request or the printer is turned over, the power light and the paper feed light are alternately flashing. After running, run clear software, the first interface selection the corresponding option click
"Ok"
Enter, programs have a prompt box, do not pay attention to
"close",
After entering the main interface, click on the left
"Maintenance
maintain
) "
Tab
,
Click
Protect Counter Check
Counter check
) "
There is a choice on the right side of it.
Clear The Protect Counter Values
Clear counter value
), "
Select Click below
"Ok"
Key execution operation. Please pay attention to the status bar below this.
"The Protect Counter Has Been Initialzed"
Counter has been initialized
).
Software prompt
30
Second initialization printer, follow the prompt operation. Note If the printer does not respond to the printer during initialization printer, the computer is not actions.
2
.
680
,
790
,
830
,
C60
,
C80
,
870
,
1290
series
These models can be done with software clearing, also available in the printer panel, panel clear reference entry
3
.
3
.
700
,
710
,
720
,
EX
,
EX2
,
EX3
,
1200
,
1270
series
These series of three-bit machine failure phenomena is the power supply and other two lights flash alternately, and the other two lights are in the same frequency. Press and hold the feedback button and the cleaning key
(
Individual machine is a change button
)
Boot
2
Loosen the paper button after seconds,
2
Seconds, release the cleaning button, press the cleaning button until all the lights are bright, the car has actions, loosen the key.
4
.
1500K
,
1500K
,
1520K
Multi-key machine series
HP
laser machine
1
.
HP 4000/4050/4100/5000 (1)
press
"
project
"
Key left
"
Numerical value
"
The left end is turned on.
(2)
When the LCD appears
"RESET Maintenance Count"
Redesign
)
When you release the keys.
2
.
HP
4500/4550 (1)
Press and hold
"
cancel
"
Key and
"
select
"
The key is open, and when the liquid crystal is lit, release the second button.
(2)
Press and hold
"
Numerical value
"
The right end of the key, then press
"
select
"
key.
(3)
You will enter after completing normal self-test
Service Mode
Service mode
)
.
(4)
press
"
project
"
Key to find
"Fuse maintenance count"
This sentence I translated into a heating component maintenance counter I don't know if it?
)
(5)
press
"
Numerical value
"
Key to find
"0" (6)
press
"
select
"
The key is saved.
(7)
press
"
carried out
"
Key machine returns
Ready
status.
3
.
HP Color LaserJet 4500/4550 (Transfer Kit Reset)
Transfer unit reset
(1)
press
"
menu
"
turn up
"RESET MENU" (2)
press
"
project
"
Key to find
"Transfer Kit Select if Done"
The transfer unit is already good
) (3)
press
"
select
"
key.
(4)
press
"
Execute key
"
Machine returns
Ready
status.
4
.
HP Color LaserJet 4500/4550 (Fuser Kit Reset)
Heating component reset
(1)
press
"
menu
"
turn up
"RESET MENU" (2)
press
"
project
"
Key to find
"Fuser Kit Select if Done"
Heating components are good
) (3)
press
"
select
"
key.
(4)
press
"
carried out
"
Key machine returns
Ready
status.
5
.
HP
Color LaserJet 4600
(Image Transfer Kit (ETB) RESET)
(1)
LCD should be displayed before the maintenance
"New Transfer Kit =
New transmission unit
)
(2)
Press the down arrow highlight
"Yes",
press
"
an examination
"
Key to reset or enter
"Configure Device" (CONFIGURE DEVICE "
Configuring equipment
)
Select
"Resets"
middle
"RESET Supplies"
Restore vendor settings
)
,select
"New Transfer Kit" (NEW TRANSFER KIT "
New transmission unit
)
, Then select.
6
.
HP
Color LaserJet 4600
Fuser Kit Reset
Heating component reset
(1)
LCD should be displayed before the maintenance
"New Transfer Kit =
New transmission unit
)
(2)
Press the down arrow highlight
"Yes",
press
"
an examination
"
Key to reset or enter
"Configure Device" (CONFIGURE DEVICE "
Configuring equipment
)
Select
"Resets"
middle
"RESET Supplies"
Restore vendor settings
)
,select
"New Fuser Kit"
New transmission unit
)
, Then select
Seduce
.
HP 8000/8100/8150
(Transfer Kit Reset)
Transfer unit reset
(1)
After the start is normal, press
"
menu
"
Key to find
"Configuration Menu" (CONFIGURATION MENU "
Configuration menu
)(2)
press
"
project
"
Key to find
"Service massage = on / off"
Service Information
) (3)
select
"OFF",
Press Select keys to save.
(4)
Shut down. Press the numerical key minus and project keys to turn on, appearing in LCD
"RESET MAINT / COUNT"
Reset counter
)
Reconnect the keys.
8
.
Color LaserJet HP 8500/8550
(Transfer Kit Reset)
Transfer unit reset
(1)
press
"
menu
"
Key to find
"Resets menus". (2)
press
"
project
"
Key to find
"RESET TRANSFER LIFE COUNT"
Reset transfer unit life
(3)
press
"
select
"
Key, then press
"
carried out
"
Key return
Ready
status.
9
.
Color LaserJet HP 8500/8550
Fuser Kit Reset
Heating component reset
(1)
press
"
menu
"
Key to find
"Resets menus". (2)
press
"
project
"
Project button
"Reset Fuser Life Count"
Reset heating component life
(3)
press
"
select
"
Key, then press
"
carried out
"
Key return
ready
status.
There are not many hands, make a look at it.
1color300
Feed key
Cleanup
Power button, let go to press the paper button
Cleanup
10
Second (ink lamp and paper feed)
2.color800
Feed key
Black cleaning
Cai Qing wash
Power on, let go, press color cleaning
3
second
3.mj1500k (k )
Switch
Fine tuning ↓
time out
Wrap
/
Change
Boot, all lights
4.color1520k
Switch
Paper feed
/
Refund
Wrap
/
Change
Fine tuning ↑
Boot, all lights
5.Proxl (XL ) Alt Font Load / Eject Pause
Boot
6.Stylus1000
Switch
Ink
/
compression
Paper feed
/
Refund
time out
Boot
7.mj500
Paper feed
Black cleaning
Cai Qing wash
