1. Set the host name / system name on the iOS-based switch: Switch (config) # hostname Hostname Sets hostname / system name on a CLI-based switch: Switch (enable) set system name Name-string
2. Set the login password on the iOS-based switch: Switch (config) # Enable Password Level 1 Password Sets the login password on a CLI-based switch: Switch (Enable) Set Password Switch (Enable) SET ENALBEPASS
3. Set remote access on iOS-based switches: switch (config) # interface vlan 1 switch (config-if) # ip address ip-address netmask switch (config-if) # ip default-Gateway IP-Address based CLI Setting remote access: switch (enable) Set Interface sc0 ip-address netmask broadcast-address switch (enable) Set Interface SC0 VLAN SETETCH SET IP ROUTE DEFAULT GATEWAY
4. Enable and browse CDP information on the iOS-based switch: switch enable switch (config-if) # no cdp enable In order to view Cisco Neighboring Device CDP Notification Information: Switch # Show CDP Interface [Type MODLE / Port] Switch # show cdp neighbors [type module / port] [Detail] Enable and browse CDP information on CLI-based switches: Switch (Enable) SET CDP {enable | disable} Module / Port In order to view Cisco Neighbor CDP Notice Information: Switch (Enable) Show CDP neighbors [Module / Port] [VLAN | DUPLEX | Capabilities | Detail]
5. Port description based on iOS-based switches: Switch (config-if) # description description-String Port Description: Switch (Enable) Set Port Name Module / Number Description-String
6. Set port speed on the iOS-based switch: Switch (config-if) # speed {10 | 100 | auto} Sets port speed on CLI-based switches: Switch (Enable) SET Speed Moudle / Number {10 | 100 | Auto} Switch (Enable) SET PORT Speed Moudle / Number {4 | 16 | AUTO}
7. Setting an Ethernet link mode on an iOS-based switch: Switch (config-if) # duplex {auto | full | HALF} Setting an Ethernet link mode on a CLI-based switch: Switch (Enable) SET Port duplex module / number {full | half}
8. Configuring static VLANs on an iOS-based switch: Switch # VLAN DATABASE SWITCH (VLAN) # VLAN VLAN-NUM NAME VLA SWITCH # EXIT SWITCH # configure Teriminal Switch (config) # Interface Interface Module / Number Switch (Config) -IF) # Switchport Mode Access Switch (config-if) # Switchport Access VLAN VLAN-NUM SWITCH (config-if) # END Configuring static VLANs on a CLI-based switch: Switch (Enable) SET VLAN VLAN-NUM [Name Name ] Switch (Enable) SET VLAN VLAN-NUM MOM MOD-NUM / Port-List9. Configuring VLAN Trunk on Based on iOS-Switch: Switch (config) # Interface Interface Mod / Port Switch (config-if) # Switchport Mode TRUNK SWITCH config-if) # switchport trunk encapsulation {isl | dotlq} switch (config-if) # switchport trunk allowed vlan remove vlan-list switch (config-if) # switchport trunk allowed vlan add vlan-list configured on the CLI switch based VLAN Trunk: Switch (Enable) Set Trunk Module / Port [ON | Off | Desirable | Auto | Nonegotiate] VLAN-RANGE [ISL | DOTIQ | DOTL0 | LANE | NEGOTIATE]
10. Configure VTP management domain on an iOS-based switch: Switch # VLAN Database Switch (VLAN) # vtp domain domain-name Configuring VTP management fields on CLI-based switches: Switch (Enable) SET VTP [Domain Domain-Name]
11. Configure VTP mode on iOS-based switches: Switch # VLAN DATABASE SWITCH (VLAN) # vtp Domain-name Switch (VLAN) # vtp {sever | cilent | Transparent} Switch (VLAN) # vtp password password Based on CLI Configure VTP mode on the switch: Switch (Enable) Set vtp [domain domain-name] [mode {sever | cilent | Transparent}] [Password Password]
12. Configuring VTP versions on iOS-based switches: Switch # VLAN Database Switch (VLAN) # VTP V2-Mode Configures VTP VETP VETS in CLI-based switches: Switch (Enable) SET VTP V2 ENABLE
13. Start VTP Trip on iOS-based switches: Switch # VLAN Database Switch (VLAN) # VTP Pruning Starts VTP Trice on CL I-based switches: Switch (Enable) SET VTP Pruning Enable
14. Configure an Ethernet-based switch: switch (config-if) # port group group-number [distribution {source | destination}] Configuring an Ethervation on a CLI-based switch: Switch (Enable) Set Port Channel Moudle / port-range mode {on | Off | desirable | auto}
15. Adjust the root path cost on the iOS-based switch: switch (config-if) # spanning-tre [VLAN VLAN-List] COST COST Adjust the root path on a CLI-based switch: Switch (Enable) Set Spantree Portcost Moudle / port cost switch (enable) Set spantree portvlancost moudle / port [Cost COST] 16. Adjusting port ID on iOS-based switches: switch (config-if) # spanning-tree [vlan VLAN-List] Port-Priority Port-Prior Tuning port ID: Switch (enable) set spantree portpri {mldule / port} priority switch set spantree portvlanpri {module / port} priority [VLANS]
17. Modify the STP clock on the iOS-based switch: switch (config) # spanning-trees [vlan vlan-list] hello-time seconds switch (config) # spanning-tre [vlan vlan-list] forward-time seconds switch ( Config # spanning-tre [vlan vlan-list] max-agent second
Modifying STP clock on a CLI-based switch: switch (enable) set spantree hello interval [VLAN] Switch (enable) set spantree fwd delay [vlan] switch (enable) set spantree maxage agingtiame [VLAN]
18. Enable or disable Port FAST feature on the iOS-based switch port: Switch (config-if) # spanning-tree portfast enables or disables Port Fast Features on a CLI-based switch port: Switch (Enable) Set Spantree Portfast {Module / port} {enable | disable}
19. Enable or disable the UplinkFast feature on the iOS-based switch port: Switch # spanning-tre Uplinkfast [max-update-rate pkts-per-second] Enables or disable UplinkFast feature on the CLI-based switch port: Switch (enable) Set spantree Uplinkfast {enable | disable} [rate update-rate] [all-protocols off | ON]
20. In order to configure the switch to a command switch of a cluster, first assign an IP address to the management interface, then use the following command: switch (config) # Cluster Enable Cluster-Name
21. In order to delete the VLAN from a relay link, you can use the following command: Switch (Enable) Clear Trunk Module / Port Vlan-Range
22. Display the VTP parameters of the management domain with Show VTP Domain.
23. Display the VTP parameter of the management domain with Show VTP Statistics.
24. The command defines the TRBRF on the Catalyst switch as follows: Switch (Enable) set vlan-name [name name] Type trbrf bridge bridge-num [STP {IEEE | IBM}]
25. The command defines the trCrf on the Catalyst switch as follows: Switch (Enable) Set VLAN VLAN-NUM [Name Name] TYPE TRCRF {Ring Hex-Ring-Num | DECRING DECIMAL-RING-NUM} Parent VLAN-Num26. Created After the TrBrf VLAN, you can assign a switch port. For Ethernet exchange, you can use the following command to assign the port: Switch (Enable) SET VLAN VLAN-NUM MOD-NUM / Port-Num
27. Command SHOW Spantree Displays the STP status of a switch port.
28. Configure an ELAN's LES and BUS, you can use the following command: ATM (config) # interface atm number.subint multioint ATM (config-subif) # lane serber-bus Ethernet Elan-Name
29. Configuring LECS: ATM (config) # LANE DATABASE DATABASE-NAME ATM (LANE-Config-Database) # Name Elan1-Name Server-Atm-Address les1-nsap-address atm (lane-config-data) # name Elan2- Name Server-Atm-Address les2-nsap-address atm (lane-config-data) # name ...
30. After the database is created, the LECS must be started on the primary interface. The command is as follows: ATM (config) # Interface atm Number ATM (config-if) # lane config database database-name atm (config-if) # lane config auto- Config-atm-address
31. Configure each LEC to a different ATM sub-interface. The command is as follows: ATM (config) # Interface atm Number.Subint Multipoint ATM (config) # lane client Ethernet VLAN-Num Elan-Num
32. Display the status of the LES with Show Lane Server.
33. Display the status of BUS with Show Lane Bus.
34. Display the LECS database with Show Lane Database.
35. Display the status of the LEC with Show Lane Client.
36. Display the list of installed modules with Show Module.
37. Establishing a VLAN with a physical interface: Router # configure terminal router (config) # Interface Media Module / Port Router (config-if) # Description Description-String Router (config-if) # ip address ip-addr subnet Mask Router (config-if) # no shutdown
38. Use a relay link to establish a connection with VLAN: Router (config) # Interface module / port.subinterface Router (config-ig) # ENCAPSULATION [ISL | DOTLQ] VLAN-Number Router (config-if) # ip address IP-Address Subnet-Mask
39. Create connection with VLAN: Router # interface atm module / port router (config-if) # no ip address router (config-if) # ATM PVC 1 0 5 QSAAL ROUTER (config-if) # ATM PVC 2 0 16 ILNI ROUTER (config-if) # Interface atm module / port.subinterface Multipoint Router (config-if) # ip address ip-address subnet-mask router (config-if) # lane client Ethernet Elan-Num Router (config-if) # interface.Subinterface Multipoint Router (config-if) # ip address ip-address subnet-name router (config-if) # lane client Ethernet Elan-name Router (config-if) # ... 40. In order to perform a dynamic routing configuration on the routing processor, you can use the following iOS command: router # i i rTING ROUTER (config) # Router ip-routing-protocol router (config-router) # network IP- NetWork-Number Router (config-router) # network ip-network-number
41. Configuring the default route: Switch (Enable) Set IP Route Default Gateway
42. Assign VLANID for a router, use the following command in interface mode: Router # interface interface number router (config-if) # mls rp vlan-id vlan-id-num
43. Enable MLSP: Router (config) # mls rp ip on routing processor
44. In order to place an external routing processor interface and switch in the same VTP domain: Router # Interface Interface Number Router (config-if) # mls rp vtp-domain Domain-Name
45. View the specified VTP domain: Router # show mls rp vtp-domain vtp Domain Name
46. To determine the management interface on the RSM or router, you can enter the following command in interface mode: Router (config-if) # mls rp management-interface
47. To verify the configuration of MLS-RP: Router # show mls rp
48. Check the MLS configuration on a specific interface: Router # show mls rp interface interface Number
49. In order to set the flow mask on the MLS-SE and do not want to set the access list on any routing processor interface: SET MLS FLOW [Destination | Destination-Source | FULL]
50. To make MLS and input access lists can be compatible, you can use the following command in global mode: Router # mls rp ip INPUT-ACL
51. When the third layer of switch is exchanged, you can enter the following commands in the privileged mode of the switch: Switch (Enable) Set MLS enable
52. If you want to change the value of aging time, you can enter the following command in privileged mode: Switch (Enable) Set MLS AgingTime AgingTime
53. Set fast aging: Switch (Enable) Set MLS AgingTime Fast FastagingTime Pkt_threshold54. Determines those MLS-RP and MLS-SEs to participate in MLS, first display the contents of the switch reference list: Switch (Enable) show mls include include
55. Display MLS Cache Record: Switch (Enable) Show MLS Entry
56. Use the command show in ARP to display the contents of the ARP cache.
57. To configure the router as a member of the HSRP backup group, you can use the following command in Interface Configuration mode: Router (config-if) # Standby Group-Number IP IP-AddRESS
58. In order to resume the role of the forwarding router, in Interface Configuration mode: Router (config-if) # Standy Group-Number Preempt
59. Accessing time and hold time parameters are configurable: Router (config-if) # Standy Group-Number Timers Hellotime Holdtime
60. Configuring HSRP Tracking: Router (config-if) # Standy Group-Number TRACK TYPE-NUMBER Interface-Priority
61. To display the status of the HSRP router: Router # Show Standby Type-Number Group Brief
62. Use the command show IGMP to determine the elected querier.
63. Start IP Multicast Routing: Router (config) # ip muticast-routing
64. PIM: Dalllasr1> (config-if) on the interface: DALLLASR1> Sparse-mode | sparse-mode}
65. Starting sparse - PIM: Router # ip multicast-routing router # interface Type Number Router # ip Pim Sparse-Dense-Mode # ip
66. Verify PIM configuration: Dallasr1> # show ippim interface [type number] [count]
67. Show PIM Neighborhood: Dallasr1> # SHOW IP NEIGHBOR TYPE NUMBER
68. In order to configure the address of the RP, the command is as follows: Dallasr1> # ip Pim rp-address ip-address [group-access-list-number] [override]
69. Choose a default RP: Dallasr1> # ip Pim rp-address advertisement RP and its group range: Dallasr1> # ip Pim sered-rp-announce type number scope ttl group-list access-list-number is managed Route Group Notice RP Address: Dallasr1> # ip Pim Send-RP-Announce Ethernet0 Scope 16 Group-List1 Dallasr1> # Access-List 1 Permit 266.0.0.0 0.255.255.255 Set a RP Image Agent: Dallasr1> # ip Pim Send -RP-Discovery Scope TTL Verify the image of the RP to RP: Dallasr1> # SHOW IP PIM RP MAPPING DALLLASR1> # SHOW IP PIM RP [group-name | group-address] [mapping] 70. Use the command IP MultiCast on the router interface TTL-Threshold TTL-Value Set TTL Values: Dallasr1> (Config-IF) # ip Multicast TTL-Threshold TTL-Value
71. Show the PIM neighbor watch with Show IP Pim Neighbor.
72. Show various records in the multicast communication routing table: Dallasr1> show ip moute [group-name | group-address] [scoure] [summary] [count] [Active Kbps]
73. To record all IP multicast packets accepted and sent by a router: Dallasr1> #debug ip mpacket [detail] [access-list] [group]
74. To configure CGMP: Dallasr1> (config-if) on the Cisco router # ip CGMP
75. Configure a multicast router to add a specific multicast group: Dallasr1> (config-if) # ip gmp join-group-address
76. Turn off CGMP: Dallasr1> (config-if) # no ip cgmp
77. Switch on the Switch: Dallasr1> (Enable) SET CGMP ENABLE
78. Verify the configuration of CGMP on the Catalyst switch: Catalystla1> (Enable) Show config set promot catalystla1> set interface sc0 192.168.1.1 255.255.255.0 SET CGMP ENABLE
79. CGMP departure setting: Dallas_sw (Enable) Set CGMP Leave
80. Modify the control port password on the Cisco device: R1 (config) # line console 0 r1 (config-line) # login r1 (config-line) # Password Lisbon r1 (config) # Enable Password Lilbao R1 (config) # Login Local R1 (config) # UserName Student Password Cisco
81. Setting the console and Vty port on Cisco devices Timeout: R1 (config) # line console 0 r1 (config-line) # EXEC-TIMEOUT 5 10 R1 (config) # line vty 0 4 r1 (config-line ) # Xc-timeout 5 282. Set privilege level on Cisco devices: R1 (config) # privilege configure level 3 Username R1 (config) # privilege configure level # privilege configure level # privilege configure level 3 ping r1 (config) # Privilege Configure Level 3 show Run R1 (config) # Enable Secret Level 3 Cisco
83. Use the command privilege to define the commands used under this privilege level: Router # privilege model level level command
84. Set User Privilege Level: Router # Enable Secret Level 3 Dallas Router (config) # Enable Secret San-Fran Router (config) # UserName Student Password Cisco
85. Sign Set and Display: R1 (config) # Banner Motd 'Unauthorized Access Will Be Prosecuted!'
86. Set Vty Access: R1 (config) # Access-list 1 permit 192.168.2.5 r1 (config) # line vty 0 4 r1 (config) # Access-Class 1 in
87. Configuring http access: router3 (config) # Access-list 1 permit 192.168.10.7 router3 (config) # ip http sever router3 (config) # ip http access-class 1 router3 (config) # ip http authentication local router3 (config ) # Username Student Password Cisco
88. To enable HTTP access, type the following command: Switch (config) # i h h h h
89. Start and verify port security on the SET command-based switch: switch (enable) set port security mod_num / port_num ... Enable Mac Address Switch (Enable) Show port mod_num / port_num starts and verifies on a switch based on CiscoIOS command Port Safety: Switch (config-if) # port secure [mac-mac-count maximum-mac-count] switch # show mac-address-table security [type module / port]
90. Create a record in a standard traffic filter table with a command access-list: Router # access-list access-list-number {permit | deny} Source-address [Source-Address]
91. Create a record in an extended traffic filter form with a command: Router (config) # Access-list access-list-number {permit | deny {protocol | protocol-keyword}} {source source-wildcard | Any } {DESTINATION DESTINATION-Wildcard | Any} [protocol-specific options] [log] 92. For the in-line routing update, the most basic command format for configuring routing updates is: r1 (config-router) # distribute-list access-list -Number | Name in [Type Number]
93. For the outgoing route update, the most basic command format for configuring routing updates is: r1 (config-router) # distribute-list access-list-number | name out [interface-name] routing-process | autonomous-system- Number
94. SET SNMP Command Options: SET SNMP Community {Read-Only | Ready-Write | Read-Write-all} [Community_String]
95. SET SNMP TRAP command format is as follows: set snmp trap {enable | disable} [all | moudle | Classis | Bridge | Repeater | Auth | VTP | ippermit | vmps | config | Entity | STPX] SET SNMP TRAP RVCR_ADDR RCVR_COMMUNITY
96. Enable SNMP Chassis Trap: Console> SET SNMP TRABE CHASSIS
97. Enable all SNMP Chassis Traps: Console> Set SNMP TRABE
98. Disable SNMP Chassis Trap: Console> SET SNMP TRAB DISABLE CHASSIS
99. Receive a record for SNMP traps: console> (enable) Set snmp trap 192.122.173.42 public
100. SHOW SNMP output results.
101. The result of the output set SNMP RMON enable.
102. Show SPAN information:
Consile> Show Span
