As is well known, the toner cartridge is the most important print component of the laser printer. Whether we can use the toner cartridge correctly, it is related to whether it can maximize its "potential" and do it. Therefore, the understanding and familiarity of the knowledge of the toner cartridges, the knowledge of knowledge is quite important, which is directly related to its vitality. Maintenance Yanshou: Very hard to visit more than a dozen shops to buy the most ideal printer to move back to the office, but don't think that you can not be too unison. The toner cartridge is a component with a higher technical content. Sometimes it will spoiled, the user cares for insufficient or accidentally ignoring it, it must have more powerful with you, or simply strike, so the maintenance of the toner cartridge It is very important. 1. Regular cleaning: Usually the toner cartridge will be more or less polluting, output text, the image will be blurred, and the gray is added to the shape, so it will be regularly cleaned. . Before cleaning, first carefully remove the components of the toner cartridge, and then wipe the dust particles of the photosensitive drum surface with a skim cotton or advanced photographic lens paper, but pay attention to prevent it to prevent its surface layer. Then, the surface is used to remove the surface with a skim cotton or high-grade photographic sheet, and the drum is applied to the surface. When wiping, it should be used to gently wipe it. After polishing, immediately use the degreasing cotton cleaner. Wipe clean. Finally, the gauze with a talc powder gently took a layer of talc powder on the surface of the drum, which can be replaced, and the entire cleaning process ended. 2. Timely remove the waste powder: After a period of powder plus powder, the waste powder in the waste powder will continue to accumulate, which will affect the printout effect, which will cause the occurrence of leakage. (The so-called leakage powder is due to the stack of waste powder, so that the produced waste powder can not enter the waste powder warehouse, and the waste powder in the waste powder warehouse will continue to "squeeze" the waste evil occurred.) The occurrence of a phenomenon will directly lead to irregular black spots on the output of the manuscript, black block, if the waste powder is not removed, the more of the waste powder, the friction pressure with the photosensitive drum is getting tight and tight The photosensitive drum plating film on the photosensitive drum will eventually be worn away, thus damaging the entire toner cartridge. The method of clearing is very simple, as long as the collection warehouse is opened, the waste powder directly removes the waste powder directly with a cotton swab or paper towel. 3. Don't let the toner cartridge overload: Anything workload has a limit, the toner cartridge is a silicone light conductor, and there is also a problem of working fatigue. If you use it for a long time, you will affect the print output effect. He will be strike, so users should remember to give a snoring time for the toner cartridge. Generally, if it is a big output, it is recommended to take a break at 8-12 hours, and it is useful for a long time, it is best to use it after a week or after a longer period of time. However, this must have an impact on the work of the user, so the author recommends that you can purchase more than two toner cartridges to use, so you can avoid the fatigue of the toner cartridge without affecting work.
Replacement of the toner cartridge is generally around 6000-10000, after a long time, when you find the output of the manuscript image, there is a serious black spot stripe, even if you have maintained a repair, the toner cartridge is The life is really the end, then it needs to be replaced. Replacing the toner cartridge is difficult to say that it is easy to say, but it is not very good. This is still a little learning. Here, the drum powder separated toner cartridge is a brief introduction. First, turn off the printer power to remove the toner cartridge, then clamp the metal pin on one side, carefully pull out (or pick up the pin directly, open the toner cartridge), in general, then we can find The toner cartridge can be divided into two parts, with a magnetic roller, and a gas selenium is a collection portion of a waste powder. First come to see the supply powder, first turn down the screws on the magnetic roller ring side, open the plastic cover, and then clean the toner of the carbon powder bin and the magnetic roller to clean it with a soft brush. Then, re-decompose the magnetic roller, and press the force to prevent the magnetic roller from being separated from the original position. At this time, it can be toned, and then pour the carbon powder and then pour it into the supply powder. The tank is fixed to fix the magnetic roller. In the end, it should be gently rotate the gear plug of one end of the magnetic roll to facilitate carbon. Uniform attachment of powder. Let's take a look at the collection section. In this section, what we have to do is replacing the new photosensitive drum. Use the same method to discharge the fixed pin, take out the drum, then clean the waste powder of the waste powder collection (to avoid the print quality of the new drums), here we can install new photosensitive drums . It should be noted when installing that the photosensitive drum is usually left and right, and the one end of the gear is applied is renewed, and the drum is nail with the fixed pin that has just been dialed. The new photosensitive drums generally have a colorful anti-exposure seal, do not tear off before installation to prevent exposure, the installation check is correct. In this way, the supply powder part and the collection portion are all made, and finally, simply install the two parts in the case of unpacking, insert the fixed card pin, and the entire replacement work is done. During the replacement process, if there is carbon powder falling outside the printer, it is best to use a vacuum cleaner, and then wipe it with a pure wine. Moreover, the entire replacement process is preferably carried out in a dark studio to prevent photosensitive drums from exposure. For the replacement of the integrated toner cartridge, it can be said that it is possible to replace the entire toner cartridge, save a lot of trouble, but remember it best to shake the toner before loading. In addition, the author also reminds you that usually the toner cartridge is valid for two and a half years, but once the validity is unpacked, only 6 months, the user should pay attention to the validity period to ensure print quality. Note: While maintaining and replacing the toner cartridge, some places need to be reminded again: 1. Clean the toner cartridge does not have to be too frequent, and ordinary paper washing in the cleaning process. 2. During the above-described maintenance and replacement, it is strictly to touch the surface of the photosensitive drum, while also preventing hard objects. 3. Try not to let the toner cartridge directly exposed under the sun or strong light source, do not casually open the flap on the toner cartridge, if the time is continuously exposed to strong light more than ten minutes, the serious words are scrapped. 4. Avoid using and preserved in high humidity, high temperatures, high-precipitation, once the toner can bake, affect printing effect or result in printing, and in addition to the toner cartridge from low temperature to high temperature It is best to put on hold for a period of time (more than an hour). 5. Do not use your hand to turn the OPC drum, and the OPC drum is rotated, it must be paying attention to the direction, if the direction of rotation is not correct, it will damage the part caused when it is printed.
