EPSON color spraying machines need to be cleared in the following types:
1.480, 580, C20, C40, C41 series
When the unknown error is displayed when the service request, the service request or the printer is turned over, the power light and the paper feed light are alternately flashing. After the online, run clear software, the first interface selects the appropriate options to click "OK" to enter, the program prompt box, do not pay attention to "Close", then enter the main interface, click on the "Maintenance" tab, click "ProtectCounter Check (Counter Check) "There is an option on the right" Clear The Protect CounterValues ", select the" OK "button under the Clear The Protect Countervalues." Please pay attention to the status bar below this. "The ProtectCounter Has Been Initialzed". Software prompts to initialize the printer for 30 seconds, follow the prompt operation. Note If the printer does not respond to the printer during initialization printer, the computer is not actions. 2.680, 790, 830, C60, C80, 870, and 1290 series These models can be done with both software clearing or using the printer panel, panel clear reference entry 3. 3.700, 710, 720, EX, EX2, EX3, 1200, 1270 series
These series of three-bit machine failure phenomena is the power supply and other two lights flash alternately, and the other two lights are in the same frequency. Press and hold the feed button and the cleaning key (individual machine is a changing key) boot, release the paper button after 2 seconds, loose the cleaning key for another 2 seconds, then press the cleaning button until all the lights are bright, the car There is a move, release the key.
4.1500K, 1500K , 1520K multi-key machine series
HP laser 1. HP 4000/4050/4100/5000 (1) Press the "Item" button to add the "value" button to the left side. (2) When the "RESET Maintenance Count" appears on the LCD, the keys are released. 2. HP 4500/4550 (1) Press and hold the "Cancel" button and "Select" button, release the second button when the liquid crystal is lit. (2) Press and hold the right end of the "Numeric" button and press the Select button. (3) You will enter "Service Mode" after completing normal self-test. (4) Press the "Project" button to find "FuseTenance Count" (this I translated into heating component maintenance counter. I don't know if it is?) (5) Press "Numeric" to find "0" (6) Press "Select" to save. (7) Press the "Execute" button to return to the READY status. 3. HP Color LaserJet 4500/4550 Reset (1) Press "Menu" to find "Reset Menu" (2) Press the "Project" button to find "Transfer Kit Select if Done" (the transfer unit is good) 3) Press the "Select" button. (4) Press the "Perform button" machine to return to the READY status. 4. HP Color LaserJet 4500/4550 (FUSER KIT RESET) Heating Component Reset (1) Press "Menu" to find "RESET MENU" (2) Press "Item" to find "Fuser Kit Select if Done" (heating component is good) 3) Press the "Select" button. (4) Press the "Execute" button to return to the Ready status. 5. Image Transfer Kit (ETB) Reset (1) Prior to implementation, LCD should display "New Transfer Kit = (2) Press the down arrow to highlight" Yes ", press" Check the button to reset or enter the "configure device", select "Reset Supplies" in "Resets", select "New Transfer Kit", then select. 6 . HP Color LaserJet 4600 (FUSER KIT RESET) Heating Component Reset (1) Prior to Implementation Maintenance, LCD Shows "New Transfer Kit = (2) Press the down arrow to highlight" Yes ", press "Check" button to reset or enter "Configure Device", select "Reset Supplies" in "Resets", select "New Fuser Kit", then select 7 .
HP 8000/8100/8150 (Transfer Kit Reset) Transfer unit Reset (1) After powering, press "Menu" to find "Configuration Menu" (2) Press "Item" button "Service Massage = ON / OFF "(3) Select" OFF "and press the selection button to save. (4) Shutdown. Press the numerical key minus and the project key minus, the "reset maint / count" (reset counter) appears after the liquid crystal appears. 8. Color LaserJet HP 8500/8550 Transfer unit Reset (1) Press "Resets Menus" to find "Resets Menus". (2) Press "Item" to find "Reset Transfer Life Count" Reset Transfer Unit Life ( 3) Press the "Select" button and press the "Execute" to return to the READY status. 9. Color LaserJet HP 8500/8550 (FUSER KIT RESET) Heating Component Reset (1) Press "RESETS MENUS" to find "Resets Menus". (2) Press "Item" project key to find "reset Fuser Life Count" reset heating component life (3) Press the "Select" button and press the "Execute" to return to the READY state. EPSON PRO10000 Engineer Cleaning Method 1. Booting method: Power button ( button) (- button) (Enter key) on the control panel Note: Press at the same time for about 3 seconds. Use the Paper Select key PAPERSORCE to repeat until the Cleanine cleaning menu button 3 is found. Press Enter 4. Use the Paper Select button PAPERSORCE to find the KK2 option 5 repeatedly. Press Enter, then the printer starts cleaning, please wait 20 minutes or so. To exit, press the PAUSE button to enter the main menu 7 on the control panel. To completely exit, please turn off the power button Note: Please try not to make a mistake when you are operational. Because these operations are impact on the printer's life, do not have the number of times when using the KK2 function. The life. The following is the repair of the Canon printer: sharing with everyone !!! One / into the maintenance mode 1 / shutdown. Press RESUM, press POWER to open the machine, the green light is on. 2 / Press and hold Power Juji, release Resum Health. Then press Resum, release Power health. (Press RESUM JC / Huang flash). 3) When the initialization begins, the green light flashes. After the green light is on, according to the number of resources (depending on the model . 4) Press Power health, execute. Canon part of inkjet machine repair mode
Canon: BJC-2000 EEPROM Clear 1. Remove the ink cartridge, press RESET, plug the source line. 2. Loosen the reset button, press this button in 5 seconds and loosen, the train will move to the middle. 3. Press and hold the reset button More than 2 seconds, loosen. 4. According to the following table, hold down the reset button. 5. Shutdown. Operation: Setting content: Press and hold 2 seconds EEPROM Clear and Target Settings (Japan) Press once (Japan) (Japan) (Japan) EEPROM does not clear) Press and hold 2 (2 intervals 1 seconds) target settings (other) (EEPROM does not clear) Canon BJC2100 EEPROM clear 1. Remove the ink cartridge, press RESET, plug the source line. 2. Loosen the reset button And press this button in 5 seconds and loosen, the car will move to the middle. 3. Press and hold the reset button for more 2 seconds, loosen. 4. According to the following table, hold down the reset button. 5. Shut down. Operation: Set Content: Press and hold 2 seconds or more EEPROM Clear Press Target Settings (Japan.bjf210) Press 2 Target Settings (Other .bjc2100) Press 3 Target Settings (SP: BJC2100SP) Canon BJC-80EEPROM Clear:
1. Press and hold the Power and Resume keys, plug the source line, and start after initialization.
2. Press and hold the Resume and CARTRIDGE key, press the POWER button until you hear 1 long 1 short beep.
3. According to the table below, press Cartridge to set the corresponding amount of waste ink.
4. Press the Resum key to set the corresponding amount of waste ink.
5. Use the Power button
(If you are 25%, 50% or 75%, you have to use the Power key. If you are 0%, you should use the Power key to open, then unplug the power cord)
Press CARTRIDGE:
default setting:
7 times
0%
16 times
25%
15 times
50%
14 times
75%
Canon BJC7000 / 7100
Maintenance mode:
1. Shut down. Press and hold the Resume key and write the Power button.
2. Set up the POWER button, press the Resume button twice before the initialization is completed.
3. After the initialization is completed, press the Resume key according to the table below to select the corresponding function.
4. Press the POWER key to execute
Press the Resume key:
Error indicator:
Features:
0 times
not bright
Exit repair mode
1 time
bright
Print eventually factory print, shut down stop
2 times
not bright
Clear EEPROM data
3 times
bright
Clear the number of ink in EEPROM
4 times
not bright
Print data in EEPROM
5 times
bright
Change the national symbol
6 times
not bright
Print the durability pattern of ordinary paper
7 times
bright
Durability pattern of printing light surface photo paper
8 times
bright
Print LF detection pattern
9 times
not bright
Restore normal model
