EPSON color spraying and HP laser counters need to be cleared in the models: 1.480, 580, C20, C40, C41 series When online, unknown errors, service requests or printers When the power light and the paper feed light are alternately flash, it can be cleaned. After running, run clear software, the first interface selection the corresponding option click "OK" to enter, the program appears in the box, does not use to click "Close", then enter the main interface, click on the "Maintenance" tab, click "Protect" Counter Check, there is an option on the right, "Clear The Protect Counter VALUES", select Click the "OK" button to perform the action. Please pay attention to the status bar below this. "The Protect Counter Has Been Initialzed". Software prompts to initialize the printer in 30 seconds, follow the prompt operation. Note If the printer does not respond to the printer during initialization printer, the computer is not actions. 2.680, 790, 830, C60, C80, 870, and 1290 series These models can be done with software clearing or printer panels, panel clear reference entry 3.3.700, 710, 720, EX, EX2, EX3, 1200, 1270 Series These series of three-bit machine failure phenomena is the power light and other two lights flicker, and the other two lights are in the same frequency. Press and hold the feed button and the cleaning key (individual machine is a changing key) boot, release the paper button after 2 seconds, loose the cleaning key for another 2 seconds, then press the cleaning button until all the lights are bright, the car There is a move, release the key. 4.1500K, 1500K , 1520K multi-key series HP laser machine 1. HP 4000/4050/4100/5000 (1) Press the "Item" button to add the "value" button to the left side. (2) When the "RESET Maintenance Count" appears on the LCD, the keys are released. 2. HP 4500/4550 (1) Press and hold the "Cancel" button and "Select" button, release the second button when the liquid crystal is lit. (2) Press and hold the right end of the "Numeric" button and press the Select button. (3) You will enter "Service Mode" after completing normal self-test. (4) Press the "Project" button to find "FuseTenance Count" (this I translated into heating component maintenance counter. I don't know if it is?) (5) Press "Numeric" to find "0" (6) Press "Select" to save. (7) Press the "Execute" button to return to the READY status. 3. HP Color LaserJet 4500/4550 Reset (1) Press "Menu" to find "Reset Menu" (2) Press the "Project" button to find "Transfer Kit Select if Done" (the transfer unit is good) 3) Press the "Select" button. (4) Press the "Perform button" machine to return to the READY status. 4. HP Color LaserJet 4500/4550 (FUSER KIT RESET) Heating Component Reset (1) Press "Menu" to find "RESET MENU" (2) Press "Item" to find "Fuser Kit Select if Done" (heating component is good) 3) Press the "Select" button. (4) Press the "Execute" button to return to the Ready status. 5.
Image Transfer Kit (ETB) Reset (1) Prior to implementation, LCD should display "New Transfer Kit = (2) Press the down arrow to highlight" Yes ", press" Check the button to reset or enter the "configure device", select "RESET SUPPLIES" in "Resets", select "New Transfer Kit", then select .6 . HP Color LaserJet 4600 (FUSER KIT RESET) Heating Component Reset (1) Prior to Implementation Maintenance, LCD Shows "New Transfer Kit = (2) Press the down arrow to highlight" Yes ", press "Check" button to reset or enter "Configure Device", select "Reset Supplies" in "Resets", select "New Fuser Kit", then select 7 . HP 8000/8100/8150 (Transfer Kit Reset) Transfer unit Reset (1) After powering, press "Menu" to find "Configuration Menu" (2) Press "Item" button "Service Massage = ON / OFF "(3) Select" OFF "and press the selection button to save. (4) Shutdown. Press the numerical key minus and the project key minus, the "reset maint / count" (reset counter) appears after the liquid crystal appears. 8. Color LaserJet HP 8500/8550 Transfer unit Reset (1) Press "Resets Menus" to find "Resets Menus". (2) Press "Item" to find "Reset Transfer Life Count" Reset Transfer Unit Life ( 3) Press the "Select" button and press the "Execute" to return to the READY status. 9. Color LaserJet HP 8500/8550 (FUSER KIT RESET) Heating Component Reset (1) Press "RESETS MENUS" to find "Resets Menus". (2) Press "Item" project key to find "reset Fuser Life Count" reset heating component life (3) Press the "Select" button and press the "Execute" to return to the READY state.
There are not many hands, make a look at it. 1color300 feed button cleaning key boot key, loose hand and press the paper transfer button cleaning button 10 seconds (ink lights and paper light flashes) 2.Color800 feed button black cleaning color cleaning boot button, let go Press color cleaning 3 seconds 3.mj1500k (k ) switch fine tune ↓ pause wrap / change page boot, all lights smash hands 4.color1520k switch paper feed / return paper wrap / change page fine tune ↑ boot, all Lights Loose Pine Hand 5.Proxl (XL ) Alt Font Load / Eject Pause Power On 6.stylus1000 Switch Tuk / Compressed Feed / Detasing Pause Power On 7.mj500 Feed Black Cleaning Color Wash Power On , Then press the paper feed button 3 seconds 8.mj510 (k) feed / returning paper cleaning power button, let go to press the paper feed / return paper for 10 seconds, see the paper feed light and the lack of ink light flash 9.colorii switch Pause paper color cleaning boot button 10.color switch font paper feed / retraction pause boot button 11.color3000 Pause Link / change page fine tune ↓ boot 12.epson Stylus Color 1500K and Epson STYLUS Color 1520k Clear the counter: Press and hold the "Alt" button, "Retail / Change" button, "Feed / Detasing" button, "Font" button, boot, hear "beep "After a sound, the machine restores normal work.
The following is the repair of the Canon printer: sharing with everyone!!! One / into the maintenance mode 1 / shutdown. Press RESUM, press POWER to open the machine, green light is on .2 / Press and hold Power Juji, release Resum Health. Then press Resum, release Power health. (Press RESUM Jujube, Light / Huang flashing) .3) When the initialization begins, the green light flashes. After the green light is on, according to the number of resums according to the number of different times (depending on the model . 4) Press POWER health, execute.
Canon printer repair clearance method: Sharing with everyone!!! One / into the repair mode 1 / shutdown. Press RESUM, press POWER to open the machine, green light is on .2 / Press and hold Power Juji, release Resum health. Then press Resum, release POWER health. (Press RESUM Jujube / Huang flashing) .3) When the initialization begins, the green light flashes. After the green light is on, it is good according to the number of different times (depending on the model.) .
EPSON PRO10000 Engineer Cleaning Method Epson Pro10000 Engineer Cleaning Method 1. Booting method: Power button ( button) (- button) (Enter key) on the control panel Note: Press at the same time for about 3 seconds. Use the Paper Select key PAPERSORCE to repeat until the Cleanine cleaning menu button 3 is found. Press Enter 4. Use the Paper Select button PAPERSORCE to find the KK2 option 5 repeatedly. Press Enter, then the printer starts cleaning, please wait 20 minutes or so. To exit, press the PAUSE button to enter the main menu 7 on the control panel. To completely exit, please turn off the power button Note: Please try not to make a mistake when you are operational. Because these operations are impact on the printer's life, do not have the number of times when using the KK2 function. The life.
4) Press Power health, execute.
Canon part of inkjet machine repair mode Canon part inkjet machine repair mode
Canon: BJC-2000EPROM Clear 1. Remove the ink cartridge, press RESET, plug the source line. 2. Loosen the reset button, press this button in 5 seconds and loosen, the car will move to the middle .3. Press and hold the reset button. 2 seconds, loosen. 4. According to the following table, hold down the reset button. 5. Turn the unit. Operation: Setting content: Press and hold 2 seconds More EEPROM Clear and Target Settings (Japan) Set (Japan) (EEPROM) Not cleared) Press and hold 2 (2 intervals 1 seconds) target settings (other) (EEPROM does not clear) Canon BJC2100EEPROM Clear 1. Remove the ink cartridge, press RESET, plug the source line .2. Loosen reset button, 5 Press this button in seconds and loosen, the car will move to the middle .3. Press and hold the reset button for more 2 seconds, loosen. 4. According to the following table, hold down the reset button. 5. Turn off. Operation: Setting content: Press and hold 2 seconds or more EEPROM Clear Press 1 Target Settings (Japan.bjf210) Press 2 Target Settings (Other .bjc2100) Press 3 Target Settings (SP: BJC2100SP)
Canon BJC-80EEPROM Clear: 1. Press and hold the Power and Resume keys, insert the source line, initialize the back. 2. Press and hold the Resume and CARTRIDGE key, press the POWER button until you hear 1 long 1 short beep. 3. According to the table below, press Cartridge to set the corresponding waste ink. 4. Press the Resum key to set the corresponding waste ink. 5. Use the Power key shutdown (if it is 25%, 50% or 75%, you must use Power Key boot. If 0%, use the Power key to open, then unplug the power cable) Press CARTRIDGE: Default setting: 7 times 0% 16 times 25% 15 times 50% 14 times 75%
