HP ink cartridge, etc.
Eleven, how can Canon's BJC-3000/6000/6500 how to add ink?
BJC-3BK / 3C / 3M / 3Y / 3PBK / 3C / 3M / 3M / 3Y / 3PBK / 3PC / 3M / 3M / 3Y / 3PBK / 3PC / 3PM ink cartridge is similar to the BJI-201 cartridge, but the ink hole is in the bottom of the ink cartridge, so the method of the ink is omitted There is a change. Revete the stickers above the ink cartridge, find a flat point on the ink ink chamber, use the tip needle of the ink water bottle (do not use the needle of the ink water), and to the expansion of the injection needle can insert, The ink chamber is filled, and the pore strip is filled with the pore strip. We noticed that there is a plug-in hole that is sealed by plastic beads, why can't you use a method of adding a 03 ink cartridge to press the plastic beads, and then seal the hole with the steel ball after entering the ink? The difference is that the 03 ink cartridge is a short life, the number of additions to the ink is limited, while the bjC-3000/6000/6500 is the long life, the ink cartridge can repeatedly ink water, and the beads that are pressed are never good.
Twelve, EPSON printer cartridges in the ink have a discontinuation process
The EPSON printer is more common because there is nothing in the use of improper ink or for a long time. Most people mistakenly think that it is blocked. At this time, it will really lead to blocked, or anxious Send repair, white flowers. In fact, the way to deal with is simple, first of all, what is the disconnection, what is a plug. When doing nozzles, the line is not continuous (there is a disconnection) may be a disconnection, or it may be blocked. At this time, it is generally a printhead cleaning. After cleaning, the nozzle is checked, once again, after cleaning a few times If the disconnection is always in the same part without changing, it is generally blocked. The blocked nozzle is the nozzle at the disconnection; if it is cleaned, the position of the disconnection is not fixed, once it is here, The time is there, it can be judged that it is not a plug, but there is air in the well, and the ink supply is discontinuous, resulting in disconnection. The solution is: First, it is determined that after each cleaning, the number of broken lines is increasing, if the first conclusion is that the ink of this color is finished, and the ink cartridge is confirmed, and it is indeed ink to add ink. You can solve the problem. If it is just added to the ink, the disconnection should be added, the air is added, and the air is present near the mouth, and the ink is entered into the hole, and the disconnection occurs. At this time, remove the ink cartridge, bomb or take a bomb, or then add a little ink, and the ink is allowed to stand down for ten minutes, put it back to the printer, and do nozzle cleaning. It should be noted that the interval between each nozzle cleaning is slightly longer (half an hour), so that the ink has a natural settlement process, and continuous nozzle cleaning effect is not good.
Thirteen, the EPSON printer cartridge is plugged in ink after ink
Here, how to judge the plug and disconnection. Most people will misunderstand the broken line, in fact, if not for a few months, or take a long time, generally do not block, the ink drying at the nozzle is generally blocked. . It is common that because some reason produces a disconnection, the user does not know how to properly, and the air in the well is the most prone to plug. After the plug, continuous nozzle cleaning is a simple and effective way to pass the empty waste, ink, practice is: move the printhead to the position of the ink cartridge (usually pressing the paper paper button for one second), Distilled water or water droplets soak it on the normally parked in the spray, let the print head reset, shut down, turn it on the next day, cleaning the printhead, do nozzle examination, plug is not very serious, generally solve the problem . If you still can't solve the problem, in the warranty period, change the original cartridge to send the maintenance center; after the warranty period, you can clean it yourself, but the process is more complicated, you need to have a strong hands-on ability. Fourteen, canon, hp, lexmark, etc., the ink cartridges, ink, and the processing of the disconnection or plug.
The common feature of the ink cartridges such as Canon, HP, Lexmark is that there is a vent hole (compatible ink hole) in the upper or side of the ink cartridge, which is used to add ink during production, and it is used to keep the ink cartridge inside and outside the air pressure. balance. The normal sign of the nozzle is that it is gently pressed in the nozzle with a facet paper, and it can be seen that each color ink is uniformly oozing. Otherwise, there is a disconnection or blocked, of course, the nozzle examination can also be seen. There are several reasons that cause the disconnect or blocked, which is usually used for a long time to be placed for a long time. The nozzle is easily clogged in a state in which no ink is ink; if the addition in ink is improper, such as internal and external pressure Improper adjustment, can also result in disconnection. The method of processing is: find a clean glass (or other plane) drop a little water, immerse the ink cartridge nozzle in water for two to ten hours (depending on the degree of view block, do not wet the contact), then wipe the nozzle with the facade It is good to exude ink. If only slight exudation is slightly, it can be blown into the ink cartridge from the vent hole, and it is better to see the ink from the nozzle. As long as the nozzle or nozzle line is not damaged, this method can solve the problem of most of the ink cartridges, and have been recorded in this method for nearly one year.
Fifteen, HP 51625a / g, 51649a / g, how does the C1816A ink cartridge add ink?
Within the package of God Jie in the three ink cartridges, there is a dedicated U-Type Opener (Opener), there are two cutting edges in the U-shaped edge, and the blade alignment cartridge is placed in accordance with the requirements of the specification. The seam of the ink cartridge is inserted, and the ink cartridge can be opened up slowly. After opening the cover, you can see the three-graphous chamber of the three colors, each with three holes, which hole ink can be injected, respectively, injecting ink, with no exceeding the housing capacity of the sea cotton. Then cover the upper cover, stop the upper cover laterally with the stationery strip. Use a paper towel to wipe the nozzle. If the ink is blocked, the ink cartridge can be returned. If the oozing is not smooth, it may be that the ink cartridge is light, and the nozzle is somewhat dry, soak the nozzle as described in the first paragraph 14. I can solve the problem.
XVI, how does the HP C1823A / D / G ink cartridge add ink?
In the rear side of the C1823A / D / G ink cartridge, there are three parallel round small holes, plugged by a plug, and topped it into the ink cartridge with a tip needle in the Shenjie ink, which is an injection hole, three holes. The corresponding color is yellow, magenta, green, and is steady, and you can try a color with a toothpick. The ink is added to the hole, and the injection pores are respectively plugged in the small bolt in the three colors of the belt. To accommodate the accommodation capacity of no exceeding the sea cotton. Use a paper towel to wipe the nozzle. If the ink is blocked, the ink cartridge can be returned. If the oozing is not smooth, it may be that the ink cartridge is light, and the nozzle is somewhat dry, soak the nozzle as described in the first paragraph 14. I can solve the problem. This method is also applicable to the 51641a ink cartridge of HP. Seventeen, BCI-3 series and BCI-5 series ink box filled ink precautions
Canon's 3000/6000/6200/6500/8200 Series BCI-3 Series and BCI-5 Series Ink Boxes are composed of two parts of the storage chamber and the seaot, and the ink often occurs outward from the nipple mouth. In the case of drops, this is because the holes on the ink chamber are too small, the needle will be able to insert, the air does not discharge when the ink water does not discharge, and the generated pressure makes the ink drip from the nipple. There are several ways to solve:
1. Keep the original packaged orange cover, press it with a rubber strip in the ink, then irrigation;
2. Expand the hole for ink ink, and leave the elongated air in the needle, so as quickly as possible, then seal the injection hole.
3. Directly take the plastic beads above the ink ink in the ink, ink, and add the ink as soon as possible.
Another thing to note is that after the ink is added, it must be carefully sealed and leaking, and the ink will flow out of the ink port.
