Epson's ink cartridge, etc.
Sixth, how does EPSON's ink cartridge add ink?
In addition to the air, the EPSON printer is brought into air, when the ink is filled, it is not properly brought to air, even more air. Therefore, when in the ink, slow injection, so that the ink is lowered to the bottom of the ink cartridge, do not leave air at the bottom of the ink cartridge. The specific method is to seal the ink hole with the transparent strip with the belt (first to dry the residual in the original sealing paper, must be sealed), uncover the sealing paper above the ink cartridge, you can see the ink of each color There are two holes in the chamber (two holes in the black ink cartridge), and there is a small trench out of the vent, the other is the injection hole, and the injection hole having a separate ink cartridge is plugged in a rubber plug, these two Both can be injected. The plus amount is limited to the accommodation of no more than the sea cotton, the ink is completed, paste the paper, pay attention not to the ventilation trenches, bounce with your fingers or gently, exclude the bottom of the sea cotton bubble. After standing for ten minutes, the ink hole is sealed, and the ink cartridge is directly returned to the printer; the ink hole is sealed with a plug, and the plug is removed, and the ink is oozing. Don't point out that the injection must be gentle, Let the ink sunstate to the bottom, so that the air is allowed to leave the air at the bottom. When printing, the disconnection occurs; because the air is present, it can't be filled with the imaginary, and there is no ink, and it is missed to block.
Seven, how to add airbags with airbags in HP?
HP's black ink cartridges include several of C1843A, 51625A, 51629A / g, and the commonly used ink is a hole in the upper surface of the ink cartridge, and the ink is added to the plug, and then the airbag is adjusted by the syringe. pressure. The shortcomings of this method are prone to fell into the ink cartridge when drilling, and the second is a need for auxiliary tool. The patented filling method for this kind of ink cartridge is: use the rubber tubes with a belt in the ink opening, docking the nozzle hole at the bottom of the ink cartridge, and squeezing the ink into the ink cartridge, and strolled a few times in the process (do not Loosen the docking of the mouth) and let the air return. After the ink is added, keep the ink cartridge inverted, with an empty bottle from the injection hole, and the ink cartridge is not exfolted from the ink hole after the ink cartridge is from the ink hole. The ink cartridge is positive pressure. At this time, the ink cartridge is coming out of the ink cartridge, which will exude ink from the injection hole and the nozzle, so the right amount of air is to keep the air pressure balance inside and outside the ink cartridge; but the air cannot be drawn too much, if the extraction is negative Pressure, it will cause printing when printing, disconnecting.
Eight, how does the 51645A / G ink cartridge in HP add ink?
At the bottom of the 51645a / g ink cartridge, there is a black circular sticker, revealing the sticker, can be seen, press the steel ball into the ink cartridge with the plastic rod with the band, and use a bottle of ink into the ink cartridge, use the C-type clamp The ink cartridge is sandwiched, tighten it with force, press the new steel bead into the hole, loosen the C-shaped clip, stick back the sticker, wove the nozzle with the paper towel, and the ink is too smooth and the ink is complete. It should be noted that before pressing the steel beads, it is necessary to clamp the ink cartridge first, so that the press-fit steel beads are slightly negatively negative, otherwise the nozzle ink can cause nozzle ink. This method is also suitable for HP 51640a / c / c / m / y, 51644c / m / y, 51650C / m / Y ink cartridge.
IX, how does the Canon BJC-600 series BJI-201 ink cartridge add ink?
The CANON BJC-600 series BJI-201 ink cartridge is the same, and the plus method is the same. The common method of ink is to drill a hole on the ink wall of the ink cartridge. After the ink, the hole is sealed with a film. The shortcomings of this method are: ink cannot be completed, and the adhesive paper is not easily secure, easy to infiltrate. The injection method of God Jie ink is: use the tip needle with a tip to insert the sea cotton in the ink hole. When the partition between the sea cotton and the ink, the slider is slightly inserted into the storage chamber. In the ink hole, the ink is squeezed into the cartridge room, and the process is squeezed several times, let the air return to the ink. The ink is filled, and the ink will automatically penetrate into the sponge. Ten, how does the ink cartridge of Epson Color 3000 add ink?
The Epson Color 3000 has four separate inks, cyan, magenta, yellow and yellow, and the structure is a tin foil sac in the plastic box, 100ml of the ink, and the sealing of the tin foil bag is a rubber nozzle. The ink cartridge is inserted into the rubber tunnel when ink cartridges, and ink is extracted from the tin foil sac. After the structure is known, the ink is extremely simple, and as long as the needle of the ink bottle is insert into the small hole of the rubber tip, it is squeezed into the ink. It should be noted that the depth of the needle is appropriate, so that it is advisable to pass the rubber tissue, so that the ink bladder can be avoided, and it is advantageous to suck the air in the capsule. In the case of a remedy of the ink, the ink is pulled out of the empty bottle, and the bumps at the bottom of the cartridge are opened with a small knife, separate the plastic box, take out the ink bladder, and dry the broken hole, bonded with a rubber strip. , Install the ink cartridge, re-add ink, and absorb the air intake air. The structure of Canon's BJI-642, the BJI-643 ink cartridge is exactly the same as the above Color 3000, and can be referred to the previous method.
