ADSL routing method for various models! ~~ (ane)
ZTE 831ADSL MODEM
How to set 831: First brush 831's built-in software to version 2.79, you can download (how to brush inside) 831 The Ethernet port IP address of the factory is 192.168.1. 1. In order to access the Telnet to 831, we now set the address of a computer to 192.168.1. *, Use ping 192.168.1.1 to see if you can access 831, no problem, continue, in DOS mode, Into Telnet 192.168.1.1, if you just brush the software, there is a password, the original password is ADSL831 then we Already logged in 831, its prompt is this >> We can use the help command to generally understand the command we can use. I don't have much to say. Teach everyone how to set up: Mode coming out is your choice of bridge mode or routing mode, choose R Enter >> R1483 Enter R1483> Delwanip All Enter (this is the setting data inside the empty, if the back is wrong, you must play again One pass this order) R1483> HOME Enter >> Then we will quickly set up the Quick Enter system will ask you to connect to the WAN in that way, we choose PPPoE. The system is also asked Ethernet IP: We play 192.168.1.1 (must be hit) then ask the subsystem mask Subnet Mask: We play 255.255.255.0 VPI: 8 VCI: 81 Authentication, We play P, and then ask our username: (how much is how much, the following two identical) Password: Repeat password:
Ok, you can press Y to save all settings. The system asks if we want to continue to settle quickly, answer N
We now do save orders. Otherwise, we have worked hard. At this time, 831 began to restart. Then our telnet connection will naturally break, wait for 831 to restart, we continue to take Telnet, use show command to see the current situation, there is no problem, we can see the PPPoE Interface IP address. That congratulations, your 831 has dials your own net. If the IP address you see is a few ???, then you will unplug the 831 power supply, plug it, you can.
After such a setting, we just set it in the TCP / IP settings in the computer. IP: From 192.168.1.2 to 192.168.1.254 subnet mask: 255.255.255.0 default gateway: 192.168.1.1 DNS: 202.96.209.5 202.96.199.133 Good Your computer can start surfing.
Now let me talk about advanced settings: Advanced settings can be used with DHCP, then your computer can use IP. Let your computer can do server, such as open FTP Server
How to do DHCP Server: Telnet to 831 >> Lan> Lan> DHCPServer 192.168.1.2 192.168.1.254> Lan> DHCPSERVER DNS 202.96.209.3 202.96.199.133> Lan> Home >> SAVE
ended. 831 will be restarted automatically, and the 831 will not be dial after restarting, so you need to pull the power
If you have servers in the intranet (such as ftp) Telnet to 831 >> PAT> PAT> AddPatin PPPOE 21 / TCP 192.168.1.5 (this means there is a 21-port open FTP service on the 192.168.1.5 computer )> PAT> Home >> Save is good, everything is completed. Zhanda 2110 Routing Set the "ADSL Configuration Program" file, display the interface as shown
In the Edit box, the Ethernet port IP address (if this item is not changed when the first configuration or configuring is configured, the default value on the interface is the correct network port IP address; if the content is modified Please fill in the last modified value) to make sure it is filled out, otherwise it cannot be configured by configuring the configuration. If the user has forgotten the network port IP, press the "Resip" button on the backplane to make the device restore the factory settings NED IP (192.168.10.1). When the first run, the ADSL Modem default is 192.168.10.1, which requires the PC's IP network card address to the IP address of the same network segment, and then modify from the configuration program as needed. After filling out the IP address, click "Next". When the program is successfully connected to the ADSL connection, the program reads the status and parameters of the current ADSL, displaying the interface as shown in Figure 2:
This interface user can select a packaged protocol (telecommunication), the optional protocol type includes: RFC1483 Bridge: Single-machine bridge method access. In this way, only one client is allowed to access the WAN in a bridge by an ADSL MODEM. RFC1577 ROUTER: IPOA way access. In this way, one client is allowed to access the WAN in IPOA in an IPOA approach, or several clients connect to WAN in IPOA approach to an IPOA approach. RFC2364 ROUTER: PPPOA way access. In this way, a client allows a client to access the WAN in a PPPOA approach, or several clients connected to the WAN in the PPPOA approach. Wuhan friends want to route online, please choose RFC2364 ROUTER
In this interface, the user can complete the PVC parameter setting for ADSL MODEM, Wuhan Friend VCI, please enter 32 appears as shown in Figure 9:
At this point, the PPPOA protocol is taken at this time, there is no need to set the line IP address, the line subnet mask, etc., which will be dynamically assigned a line IP address when dialing. So just fill in the editing box of ADSL MODEM in this interface (Wuhan friends do not need to modify it) and the user name and password given by Telecom. After the parameters are filled, click "Finish", and the configuration program begins to configure the ADSL MODEM.
When the configuration program completes the configuration of the ADSL MODEM configuration, a message box is popped up.
Datang Telecom A-400 opened the route because there is no more cats in the hand, so it can only be used as an example, its setting is relatively simple, just less functional! Web Settings interface, as the name suggests, is to connect with the browser! According to the default IP of the manufacturer on its instructions. Enter 192.168.1.1 on the browser address bar Enter the setup interface! (If you have any case where you can connect, please set the network card IP to 192.168.1.x (2-255), then open its setup interface, first jump out of the network login box, prompt to add the account number given by the manufacturer and Password, then determine! The connection to all ADSL cats or routers is the same, but may have different default IP, account, password! After entering the settings, the following interface will appear, but each manufacturer is The interface is not the same, even will make more functions, but the main function is similar! The default status is the top 1483 bridge mode, that is, the model does not open the route! Below my choice mode is "2516pppoe" this is Virtual dial routing mode! Some settings below will add "account" "password" input box! Add the account number and password to the telecommunications, the following DNS can be filled in the DNS of the telecommunications! The value behind the "virtual path indicates VCI" and "virtual channel indicates VCI" must be the same as the telecommunications, which can ask telecommunications, will give you! But most telecom uses the default value! After determining saving, the route is open, Very simple, other cats have the possibility of page design, but the basic setting is the same! The following is about the routing settings of the fixed IP, it is also very simple, just select 1577 routing mode or 1483 routing mode and then the following settings will appear Box, in fact, some manufacturers do not have these 1577, 1483 and other numbers, just more direct writing to static IP, or wide area network IP mode. These are fixed IP settings interface! VPI, VCI, packaging forms don't say, I can't fill in the wrong! The following WAN IP, mask, gateway, DNS must fill in the telecommunications given! After determining the saving, implement routing function! The following is the setting of the local area network of the cat, generally the default What is displayed above! The following DHCP is automatically assigned or manually assigned IP mode selection, as well as the number of submathers that can be supported! Because the routing function of the cat is relatively simple, the number of sub-machines supported in general is not More, usually around 30, such as this cat's limit is the best, add more possibilities that can no connection or loss of packet loss, etc., the number of specific supports can be tested! "Status Monitor" Generally displaying the situation of network connections and data transmission traffic! Another is to display routing tables and other functions! "Account Password" Enter the Cat Settings interface The default manufacturer's set account password is changeable, you can make it according to yourself I want! UT Star Kang ADSL opens the route to 192.168.1.3, subnet 255.255.255.0, in the browser address bar, 192.168.1.1, Username: admin, password: utstar, enter the web page interface .
Then it is "LAN" option, this is not changed!
Then it is the "WAN" option, which is the focus of modification! Open the "ATM VCC" option under "WAN",
Add, the following interface, fill in the VPI / VCI value, pay attention: If there is VPI / VCI between AAL5-1 ~ AAL5-4, you must modify it to other things, you can add you. ! ! Another "PPP" item "WAN" will be deleted in the only protocol inside!
In the "EOA" item of "WAN",
Then "Add", as shown, the interface must be added in "ATM VCC". The default route is selected!
Then click on the "DNS" item of the Service item to add Telecom's DNS.
Don't forget, you have to "submit" every step, then go to the "management" item, click "Submit", etc. After submit success, save the restart ", the rest does not have to change, then the ADSL and machine power-on restart Once, wait a little 5 to 6 minutes after booting, ok, the route is successful, can be online between 192.168.1.3 ~ 192.168.1.254 ~! ! ASUS AAM6000EV
Configure the IP address of the computer network card to 192.168.1.2 mask: 255.255.255.0. If you install PPPoE virtual dial-up software, the gateway does not fill. If either routing mode. The default gateway is 192.168.1.1.
Open the PC's browser, type in the address bar: 192.168.1.1 Enter, enter the username "root" and password "root" (or ADSL / ADSL1234) at the prompt window. Configuration main page for ADSL routers
There are two ways to access PPPoE mode: 1. Establish a connection through the virtual dialing of the PC, share multiple users with multiple users, and see Seven 2 in the router configuration process. The PPPoE Client built into the ADSL router is set up with the local server to make multi-user sharing through the NAT protocol. Now the second mode is configured.
● Establish a PVC channel to use for PPPoE. If the PVC channel is not in the factory setting value, follow the steps described above -> If the factory configuration has the corresponding PVC settings, please remove the 1483B link according to the bridge menu -> 1483b Delete 1483B interface.
● In the WAN form, click PPP, click Add, the PPP Configuration page, enter the corresponding value: PPP Interface: PPP connection number 0 ~ 7 ATM VC: Available PVC channel IPF TYPE: Please select START or Startondata Protocol: Select PPPoE Service Name: You can not fill in Use DHCP: If enable, the router will get other information other than IP. Use DNS: If you open, DNS information obtained from PPP will be assigned to a local area network user as the DNS information of the router DHCP Server. DEFAULT ROUTE: Please select Enable Security Protocol: Set Login Name according to the local authentication mode: Username Password: Password Submit To save the configuration, in the Admin form, click Commit & Reboot, click the Submit button. Complete the configuration of KM300A-G
1. The default IP of this ADSL is 192.168.1.1, so set your machine to 192.168.1.x before setting (X can be any value from 2 to 255), and Mask is set to 255.255.255.0. Enter 192.168.1.1 in IE to enter the configuration interface, the default user name and password are all root. If you have changed the default IP of ADSL, please log in with your own way. 2, if you have also modified this cat, please go to "Manage / Submit & Restart", select "Restart mode" to "Reboot from Default Configuration", then restart. After a while, press 1 to log in. This step is only to its default settings. To reduce unnecessary trouble. 3. In the device information page of the home page (the picture below is already set), follow the text below, this figure is used as a reference.
4, pay attention to the picture of the red circle, the default is 8/35, and the exact letter of our electric credit is also 8/35, so it is necessary to modify this value. If your telecommunications is not this value, please Modifying is the item for this value; if there is no value to the value at this inside, then don't modify it. Modifying: 5, click Quick Settings in the Home. As shown below, the red part is provided according to the value of the value provided by Telecom. In the ATM interface, select 5 because the system already has four, cannot be used. Operating mode Selecting an Enable Brige Select Disible to refer to the following figure.
6. After the last step is determined, there will be 1,2 in the first picture in the device information of the home page. After a while, the first state light will change green, and it has been successful. Automatically obtain the IP address. Sometimes the fifth step is not necessarily success, you can disconnect the ADSL power first, try again, will be successful. However, make sure the ATM interface is not occupied, and the VPI / VCI combination does not appear in other interfaces.
7, this step is set to the local area network for DHCP mode, so you can save a lot of trouble. Select DHCP mode "DHCP Server" in the local area network / DHCP mode, press OK.
8, now on the home / device information is really as shown in each picture. Now there is an item for a project and a network mask of 0 in the "Route / IP Routing" top. And there are several dynamic IP addresses. This is successful! Finally, in "Management / Submit & Restart", submit it, submit your modification, then restart, write your modification into the memory of the cat, after a while, the cat will automatically pull the line, and start Routing.
9. Finally, the settings of the client: Dynamic IP: The client IP address is set to automatic acquisition, DNS is automatically acquired, and the rest is not available, it is OK. Static IP: The client IP is set to the address, the gateway and DNS on the same network segment of Modem, all OK! Oh, busy for a long time, it should be, I don't know if there is any omission? I hope everyone will add! ASUS AAM6000EV
The younger brother recently installed several units with ADSL Jiannan, I recommend this ASUS AAM6000EV (simple menu, but all Chinese), now many big cities ADSL has developed very fast, so ADSL MODE / router must Put the fire, less nonsense, my experience is as follows: 1; Virtual dialing, enter wide area network settings, select the ATM interface, it determines the VPI / VCI value, "We are generally VPI: 8, VCI: 35), package format QoS, PCR is default, IGMP, NAT, default routing enabel, gateway IP address default, user name, password, the user name, the user name, the user name, the password is installed in installation ADSL is Already given to you, status Select START, Auto DNS Select License, Main DNS, Supreme DNS asked Local ISP, (Qingdao is 202.120.134.68, 202.120.128.68) Fill in the home page will see one The new path, and the state is green, 2: Routing does not need to set, factory has set up 3: Enter the DHCP configuration page, DHCP mode Select DHCP Server 4: Customer Machine No settings You must choose Auto Get IP, otherwise not access Huawei (Huawei) SMARTAX MT800A work started: all lines are all connected, set IP on the PC: 192.168.1.x (x = 2-8), mask: 255.255.255.0 Gateway: 192.168.1.1 (Enter the network, I forgot Click "Add "Otherwise, if it is not input), the system prompts to restart, enter the system again, open the browser, enter the address bar input: http://192.168.1.1 and press Enter to enter the Smartax MT800A Settings screen. I will not trouble screenshots because I have not difficulty in operation.
Key: Configuring PPPoe
Step open the web page "ATM Setting";
Step 2 Pull the text block in the drop-down list of the "Connection Type" field to select "PPPoE LLC" option;
Step 3: Modify the Operation Mode to Enable.
Step 4: In accordance with the information provided by the ISP or system supplier, fill in the appropriate fields in the appropriate field, such as "VPI", "VCI", "PPPoe username", and security protocols, " PPPOE Password Password "and other values, Default Router (default route) is modified to enable;
Step 5 Correctly Enter the correct input of the value correctly, click the <"submit>" button below the field to enter the input ADSL terminal;
Step 6 ensures that the NAT value is "enable", which is enabled by default.
Step Seven DHCP's default is "DHCP Server" is not enabled, you can decide whether to enable as needed.
Step 8 points to select "Save & Reboot" directory in the web page, select "Reboot" in the "Reboot Mode" dialog, click the
Thank I, Amen! After saving, open the webpage ~~~~~ Star Kang UT300R
1. Set VPI in the WAN, VCI doesn't have to say, according to local settings (the back IP, mask, gateway is not set); 2. The package protocol sets PPPoE LLC, the bridge is set to close; 3. Fill in the username and password, check the PAP, automatically connect to select; 4, set up virtual circuits, this is the most critical step, and the main reason for many friends set failure, the virtual circuit is 0 ~ 7, according to the local situation (I Here is 0, it seems that there are 0) set one, then select "Enable" on the top left of the screen, the key is that the remaining 7 virtual circuits must be turned off, set by one, every choice, The top left is closed, so on, so that you don't have to turn off the 7 all close, remember, you will submit it once. 5. Selected NAPT in the NAT of the console. By the way, the user name that enters the setting interface is admin, the password is UTSTAR, so that the route setting is successful. Shanghai Bell Cyberlink 6307 YG1, ensuring that the computer network card IP address is 192.168.1.2, the mask is 255.255.255.0, and can be set to 202.96.209.133 The standby DNS is set to 202.96.209.5 The above 2 DNS is Shanghai, other regions can check http://ddj88.myrice.com/internet/broadband/vpi-vci.htm 2, run the clcom.exe program for modem configuration, the default password is "password"
3. Modify the VPI / VCI value according to the local line parameters and fill in the username and password. Click Apply to save the settings. This cat is 0/35 by default
Shanghai's Eastern District 0/32 West District 8/81
DNS: 202.96.209.133 202.96.209.5
. Here is usually available in the default setting.
View Route Table, if there is a record similar to the map, you have successful you have successfully modified. ASUS AAM6005HW
1, network environment MODEM is connected to HUB, ASUS 6005AAMHW's default address is 192.168.1.1, here I changed him into 192.168.0.1, and restarted MODEM, I set my machine IP to: 192.168.0.168 255.255.255.0 Default Gateway 192.168.0.1 2, input 192.168.0.1 As shown below
User ADSL password ADSL1234 appears after [Note, if your MODEM is limited, it may not be automatically dial, the solution is to download the software, upgrade your modem]
3 Click Channel to click on Action Item After selecting Delete, click Submit Clear it set the original setting, wait ... DONE, click Reset Modem to restart modem, then click here to click Add to join a new one Set, as shown below
Special explanation, I said that there will be six options in this, such as non-restricted modemServiceType, and limited MODEM may only have three, and we choose the sixth, VPI / VCI According to local telecommunications, if you don't know, local settings, telecommunications does not tell you, you can go here to see if there will be your setting http://ddj88.myrice .com / Internet / Broadband / vpi-vci.htm
4 After clicking Submit appears below and sets the zone 1: Enter your user and password diagram area for telecom application Broadband 2: Select UP [If set correctly, you will automatically log in within 30 seconds after the MODEM power Internet] Figure 3: The first must be hooked, because after a while, [NAT makes the MODEM port mapping function, Auto Discovery DNS from PPP is specified whether the Modem state can automatically return local DNS information, possibly I understand this sentence, if not, please forgive me] 5: Submit this action again, restart modem 6: Set your DNS again, if you don't know, I think it will be in this URL. HTTP: / /ddj88.myrice.com/internet/Broadband/vpi-vci.htm This is simple, I don't say much, let you restart Modem, you will restart, this is not to restart, I can't remember,
7: Take a look, your virtual automatic dial has been successful, click on the PPP under Statistics, click Status to see, is it as follows: If so, explain your virtual automatic dialing success.
8: Ok, after the virtual dial is completed, now is how we have to think about the external network users through routing, the various types of services in the intranet, where the port mapping can complete this feature. 9: Under this interface, here I have already set it, I don't want to delete it anymore, I will talk, I hope everyone can understand, I have added three ports, if, you still want to join the 22-port to do other Service, write the parameters as shown below, then submit it. I should pay attention to this, if you want to delete it, you will choose Delete No: Write the port you want to delete, then submit, pay attention, after you write, you must choose an action. : Save again submit again, if not, if your modem is powered down, you will have these settings, here, I still want to explain, 3389 port, this is the RPC [Remote Desktop] One port, that is, if the user wants to control the machine of this machine through the remote desktop on the Internet, please join this port to facilitate remote maintenance.
10: This is to arrange your http / ftp server. If you install SRV-U and IIS, the peanut shell, I will not tell [this kind of tutorial], just to specifically explain this How to set it correctly, you can enter your domain in your local area [here to assume your domain name is aaa.vicp.net] You will see the Modem configuration interface, this is normal, so, if you are customized After you have finished, you want to test, only, you are not in your intranet machine to access your domain name server [such as dial-up Internet access to test if your settings are feasible], see if you can access it normally [of course, if, you are in you On the inside of the Internet, enter your server's intranet IP can not access it normally, that is, we will set it back to normal. 11: Question: here, I want to mention a question, I hope everyone will give an explanation, I found a situation, I don't know why, I will set the Successful FTP only to set it to the following picture, I don't know Why [If it is normal setting to access the FTP, the message will not be a list] Auntie SPEED TOUCH 515 external PPPoE configuration manual Description: In the configuration parameters, if the PVC that needs to be configured, please Reconfigure after deleting the original link! !
First, USB driver installation
1. Put the CD with the USB drive into the optical drive, double click "setup.exe";
This topic related pictures are as follows: Click "Next", follow the prompts to connect Modem and PCs with the USB cable. The installation driver is displayed. The related pictures of this topic are as follows: 3, the driver installation ends.
Second, PPPOE mode parameter configuration 1, connect PC and MODEM using the USB or Ethernet line. With DHCP (also manually set the IP address of the PC to 192.168.1.2, subnet mask 255.255.255.0). Open IE and enter 192.168.1.254 in the address box;
The related pictures of this topic are as follows: 2, click "Expert Mode" to enter the following interface. Click "Continue"; this topic is related to the following: Bridged ", DSL Configuration One Selection" Multi (Auto) ". Click "Configure"; this topic related pictures are as follows: In the corresponding box, fill in the connection name, VPI / VCI, and select the package; click "Apply"; this topic related pictures are as follows: Click in the interface appearing "Save config"; this topic related pictures are as follows: You can dial the Internet after installing the dialing software.
E. TAK TD2001: I am using http://www.tek-td.com/intro-frame.htm to introduce! TP-LINK TD8830 Routing Port Mapping Map
The configuration process enters "192.168.10.200" and "Enter" in the IE address bar. Enter the default management username and password "root" into the management interface in the pop-up login dialog box. And select "Basic Config → PAT" in the menu bar on the left side of the management interface, and enter the Port Mapping Configuration dialog. In this dialog, click the "Add" button to add a new mapping item. 1. In the "Protocol" column, we can choose two protocols: TCP and UDP. Since Web services and FTP services use TCP / IP protocol, the default setting TCP is retained. 2. In the Interface box, the default value is "LAN", we can also choose ATM1, ATM2, until ATM8. Here we choose ATM1 (don't choose LAN, otherwise mapping cannot be successful). 3. "Service Name" is used to indicate categories of the map, you can enter "FTP" in any input, for example to configure an FTP mapping. 4. In the "Port Number" column, fill in the port that the ADSL MODEM is open for a variety of services, it is recommended to use the default ports of various services, such as mapping the FTP service, and enter the 21 port directly. This makes it easy access to visitors. If the default port of various services is not used, the visitor must use the IP address port number to access the released service. Assuming that the public IP address of the ADSL Modem is 218.70.130.155, but the port on which the FTP service is turned on is not 21, but 8021, the accesser from the Internet must access the FTP via "ftp://218.70.155:8021" service. 5. "Server IP Address" refers to the private IP address of the computer's computer. In this example, the IP address of the FTP server and the web server is 192.168.10.111.6. "Server port number" refers to the port that the server is turned on for its own service. In this example, the FTP server and the web server use each other. The default port: 21 and 80 mapping items After adding, click the "Finish" button to complete the settings. Then select "Save & Restart" in the left menu bar, first click on the "Save" button to save the settings first, then click the "RESTART" button to restart ADSL MODEM (Note: Be sure to follow this order! Otherwise The configuration just conducted will not be saved). After the ADSL MODEM is restarted, the Internet users can access the various services of "internal" computer through the ADSL MODEM's public IP address. Second, the character interface management method premise: PRESTIGE 642R's factory default IP address is 192.168.1.1, suppose we have enabled its routing function (see the specific configuration process of routing function "," Computer News "No. 35 F5 version" Route ADSL MODEM Network Sharing "One Text) and has been connected to the Internet. At the same time, the IP address of the computer that shares the route online is 192.168.1.2 and 192.168.1.3, the former has a web server, using the default web service port 80; and the latter has an FTP server, which is the default FTP service port 21. Configuration Procedure 1. Enter "Run" on any computer (such as 192.168.1.2) connected to ADSL Modem, "Telnet 192.168.1.1" command and execute, in the password prompt box Enter the factory default password 1234 to enter the MODEM's primary management interface (Figure 2).
2. In this management interface, enter "15" to enter the "SUA Server Setup" dialog box of "Advanced Applications", here is the port mapping setting interface of the inventive PRESTIGE 642R. 3. We can set up 8 port mapping items. The setting is very simple, first move the cursor to a blank item, then fill in the service port number provided by the intranet server on the left, and the onit server IP address is filled in the right side. For example, the service port on the web server is 80. The IP address is 192.168.1.2; the service port on the FTP server is 21, the IP address is 192.168.1.3 (Figure 3). 4. After completing the settings of this menu, press the "Enter" button to store the set value after "press Enter to CONFIR ESC to Cancel". When the MODEM is restarted, the Internet user can access the various services of "internal" computer through the ADSL Modem's public IP address.
Perhaps careful readers have found that in the port map of the TD8830, we can choose the port published by the ADSL Modem. For example, the default FTP port 21 of the intranet's FTP server port, but we publish it to the Internet through the port mapping, You can choose another port (such as 8021). Since the inquiry PRESTIGE 642R does not select an item for foreign release ports, the external publish port can only correspond to the port used by the intranet service. For example, the FTP server of the intranet uses a 21-port. The external release is also 21 port; if the intranet is 8021 port, the external release is also an 8021 port. The factory IP of these three modems is 192.168.1.1. Username: ZXDSL. Password: zxds
ZXDSL 831 is an external ADSL user device (ATUR) that realizes the separation of speech and data, completes reception and transmission of user-end ADSL data. ZXDSL 831 provides users with 1 10BASET Ethernet interface, support bridge and routing. There are two ways to access the PPPOE (virtual dialing): the first is to establish a connection through the virtual dial of the PC, and more user sharing is achieved by the proxy server. Of course this method is not the focus of today. The second is to establish a PPP connection through the ZTE831 built-in PPP connection, and multi-user sharing is performed through the ZTE831 NAT protocol. The steps of this approach are as follows: 1. First establish the PVC channel to which the current PPPoE is connected is VPI / VCI. The factory configuration of ZTE831 has been built into four PVC channels. The following is a 0/35 channel of the VPI / VCI in the location of the author. 1. The factory IP of ZTE ZTE831 is 192.168.1.1, so that the TCP / IP in the computer's network connection properties must be modified to 192.168.1.3, as shown in Figure 1
The related pictures of this topic are as follows: Open IE, type http://192.168.1.1 in the address bar, then enter the username: zxdsl; password: zxDSL can enter the setup interface in the user login bar. Figure 2.
This topic related pictures are as follows: 2. Click "WAN" and click "ATM VC" to enter the "ATM VC" view and setup page. Here you need to find the VPI / VCI value we use. The current VPI / VCI is 0/35, according to this we can see the corresponding "interface" item is "AAL5-1". Figure 3.
This topic related pictures are as follows: 3. Next, click "IPOA" to enter "EOA" view and set the page. Here, according to the "AAL5-1" we have obtained, "The Interface" is "EOA-1" it will be found according to the previous step. This is the EOA interface we have to use, as shown in Figure 4. Because the factory configuration does not have related settings, we need to delete the EOA to reset it. The related pictures of this topic are as follows: 4. Before deleting the EOA, first delete the bridge corresponding to the EOA. Click "Bridge" to enter the bridge mode setting, delete the bridge corresponding to "EOA-1". Figure 5. Click the "OK" button in the pop-up confirmation window.
The related pictures of this topic are as follows: -------------------------------------------- ------------------------------------ 5. Click "RFC 1483 Interface (EOA" to enter the EOA settings page. Figure 6. The related pictures of this topic are as follows: -------------------------------------------- ------------------------------------ Delete "EOA-1" interface. Figure 7. This topic related pictures are as follows: 6. In this way, the bridge method corresponding to the current VPI / VCI is 0/35 is deleted. The settings of the corresponding PVC channel are also completed. Second, the second is to carry out corresponding routing settings. 1. Back to the "WAN" page, click "PPP" to enter the PPP Settings page. Figure 8.
The related pictures of this topic are as follows: This topic is related to the following:. Click the "Add" button to fill in the correct settings in the PPP Interface - Add page: PPP Interface: PPP connection number 1-23 ATM VC: Available PVC channel IPF TYPE: Select Public Status: Select Start or Startondata Protocol: Select PPPoE Service Name: You can not fill in Use DHCP: If enable, the router will get other information other than the IP. USE DNS: If Enable, the DNS information obtained from the PPP will be assigned to the DNS information of the router DHCP Server to domain DEFAULT ROUTE : Select Enable Security Protocol: Set the Login Name in accordance with the local authentication method: The username Password provided by the part is as shown in Figure 9.
This topic related pictures are as follows: 3. Click Submit to complete the routing setting as shown in Figure 10. The related pictures of this topic are as follows:
